データシートサーチシステム |
|
TMP141 データシート(PDF) 9 Page - Texas Instruments |
|
|
TMP141 データシート(HTML) 9 Page - Texas Instruments |
9 / 19 page TMP141 SBAS347 − MARCH 2005 www.ti.com 9 Read and Write Transactions A complete Read transmission consists of a Start Bit, the device number, the Register Number, R/W = 1, the data bits, an even parity bit, and an Acknowledge bit. The most significant bit is sent first. Read Transaction START DEVICE NUMBER REGISTER NUMBER R/W 8 or 16 DATA BITS EP ACK M M M M M M M M M M M S … S S M A complete Write transmission consists of a Start Bit, the device number, the Register Number, R/W = 0, the data bits, an even parity bit, and an Acknowledge bit. Write Transaction START DEVICE NUMBER REGISTER NUMBER R/W 8 or 16 DATA BITS EP ACK M M M M M M M M M M M M … M M S M indicates that the bit is initiated and controlled by the master. S indicates that the bit is initiated by the master but controlled by the slave; if the data is a ‘1’, the slave lengthens the time that the bus is held low to signal a ‘1’. The device number is three bits long. Device number 0 is reserved for a broadcast to all devices, leaving address space for seven slaves. The Register Number is six bits long. The R/W is a ‘1’ for a read operation. The R/W bit is a ‘0’ for a write operation. All data bits are started by the master pulling the bus low. The TMP141 will detect the bus being low within time tSFEdet. If it is a read transaction and the TMP141 needs to send a ‘1’ for that bit period, it will hold the bus low for time tSLout1. In a Write operation, the data bits and parity are sent by the master. In a Read operation, the data bits and parity are sent by the TMP141. Data length is eight bits for registers 0, 4, and 20h. All other registers are 16 bits long. The number of bits transmitted or received depends on the length of the register: 8 bits for an 8-bit register and 16 bits for a 16-bit register. Even parity (EP) is used on the SensorPath. The parity calculation includes all bits after the Start Bit, up to and including the parity bit. Thus, the parity calculation includes the device number, the Register Number, R/W, the data bits, and the parity bit. In a Write operation, the TMP141 checks the parity sent by the master before generating the Acknowledge bit. The Acknowledge bit is sent by the receiving unit. In a Write operation, the Acknowledge bit will come from the TMP141. In a Read operation, the master generates the Acknowledge bit. ACKNOWLEDGE Bit Definition: 1: A complete data transmission was completed without a parity error. 0: An error was detected. (BER in the Status Register will be set. An Attention Request will be generated.) |
同様の部品番号 - TMP141 |
|
同様の説明 - TMP141 |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |