データシートサーチシステム |
|
74ALVT162823DL データシート(PDF) 5 Page - NXP Semiconductors |
|
74ALVT162823DL データシート(HTML) 5 Page - NXP Semiconductors |
5 / 14 page Philips Semiconductors Product specification 74ALVT162823 2.5V/3.3V 18-bit bus-interface D-type flip-flop with reset and enable with 30 Ω termination resistors (3-State) 1998 Aug 27 5 RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER 2.5V RANGE LIMITS 3.3V RANGE LIMITS UNIT SYMBOL PARAMETER MIN MAX MIN MAX UNIT VCC DC supply voltage 2.3 2.7 3.0 3.6 V VI Input voltage 0 5.5 0 5.5 V VIH High-level input voltage 1.7 2.0 V VIL Input voltage 0.7 0.8 V IOH High-level output current –8 –12 mA IOL Low-level output current 12 12 mA ∆t/∆v Input transition rise or fall rate; Outputs enabled 10 10 ns/V Tamb Operating free-air temperature range –40 +85 –40 +85 °C DC ELECTRICAL CHARACTERISTICS (3.3V "0.3V RANGE) LIMITS SYMBOL PARAMETER TEST CONDITIONS Temp = -40 °C to +85°C UNIT MIN TYP1 MAX VIK Input clamp voltage VCC = 3.0V; IIK = –18mA –0.85 –1.2 V VOH High-level output voltage VCC = 3.0V; IOH = –12mA 2.0 2.3 V VOL Low-level output voltage VCC =3 0V; IOL = 12mA 05 08 V VOL Low-level out ut voltage VCC = 3.0V; IOL = 12mA 0.5 0.8 V VRST Power-up output low voltage6 VCC = 3.6V; IO = 1mA; VI = VCC or GND 0.55 V VCC = 3.6V; VI = VCC or GND Control pins 0.1 ±1 µA VCC = 0 or 3.6V; VI = 5.5V Control ins 0.1 10 II Input leakage current VCC = 3.6V; VI = 5.5V 0.1 10 µA VCC = 3.6V; VI = VCC Data pins4 0.5 1 VCC = 3.6V; VI = 0 0.1 -5 IOFF Off current VCC = 0V; VI or VO = 0 to 4.5V 0.1 ±100 µA Bus Hold current VCC = 3V; VI = 0.8V 75 130 IHOLD Bus Hold current Dinputs7 VCC = 3V; VI = 2.0V –75 –140 µA D inputs7 VCC = 0V to 3.6V; VCC = 3.6V ±500 IEX Current into an output in the High state when VO > VCC VO = 5.5V; VCC = 3.0V 10 125 µA IPU/PD Power up/down 3-State output current3 VCC ≤ 1.2V; VO = 0.5V to VCC; VI = GND or VCC OE/OE = Don’t care 1 ±100 µA IOZH 3-State output High current VCC = 3.6V; VO = 3.0V; VI = VIL or VIH 0.5 5 µA IOZL 3-State output Low current VCC = 3.6V; VO = 0.5V; VI = VIL or VIH 0.5 –5 µA ICCH VCC = 3.6V; Outputs High, VI = GND or VCC, IO = 0 0.05 0.1 ICCL Quiescent supply current VCC = 3.6V; Outputs Low, VI = GND or VCC, IO = 0 3.9 5.5 mA ICCZ VCC = 3.6V; Outputs Disabled; VI = GND or VCC, IO = 05 0.06 0.1 ∆ICC Additional supply current per input pin2 VCC = 3V to 3.6V; One input at VCC–0.6V, Other inputs at VCC or GND 0.04 0.4 mA NOTES: 1. All typical values are at VCC = 3.3V and Tamb = 25°C. 2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND 3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10msec. From VCC = 1.2V to VCC = 3.3V ± 0.3V a transition time of 100 µsec is permitted. This parameter is valid for Tamb = 25°C only. 4. Unused pins at VCC or GND. 5. ICCZ is measured with outputs pulled up to VCC or pulled down to ground. 6. For valid test results, data must not be loaded into the flip-flops (or latches) after applying power. 7. This is the bus hold overdrive current required to force the input to the opposite logic state. |
同様の部品番号 - 74ALVT162823DL |
|
同様の説明 - 74ALVT162823DL |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |