データシートサーチシステム |
|
NCP348 データシート(PDF) 3 Page - ON Semiconductor |
|
NCP348 データシート(HTML) 3 Page - ON Semiconductor |
3 / 12 page NCP348 http://onsemi.com 3 PIN FUNCTION DESCRIPTION Pin No. Symbol Function Description 1 4 5 IN POWER Input Voltage Pin. This pin is connected to the power supply. The device system core is supplied by this input. A 1 mF low ESR ceramic capacitor, or larger, must be connected between this pin and GND. The three IN pins must be hardwired to common supply. 2 GND POWER Ground 3 FLAG OUTPUT Fault Indication Pin. This pin allows an external system to detect a fault on IN pin. The FLAG pin goes low when input voltage exceeds OVLO threshold or drop below UVLO threshold. Since the FLAG pin is open drain functionality, an external pull up resistor to VCC must be added. 6 7 OUT OUTPUT Output Voltage Pin. This pin follows IN pin when “no fault” is detected. The output is disconnected from the Vin power supply when the input voltage is under the UVLO threshold or above OVLO threshold. The two OUT pins must be hardwired to common supply. 8 NC OPEN No Connect 9 NC OPEN No Connect 10 EN INPUT Enable Pin. The device enters in shutdown mode when this pin is tied to a high level. In this case the output is disconnected from the input. To allow normal functionality, the EN pin shall be connected to GND to a pull down or to a I/O pin. This pin does not have an impact on the fault detection. PAD1 PAD1, under the device. See PCB recommendations page 10. Can be shorted to GND. PAD2 The PAD2 is electrically connected to the internal NMOS drain and connected to Pins 4 and 5. See PCB recommendations page 10. MAXIMUM RATINGS Rating Symbol Value Unit Minimum Voltage (IN to GND) Vminin −0.3 V Minimum Voltage (All others to GND) Vmin −0.3 V Maximum Voltage (IN to GND) Vmaxin 30 V Maximum Voltage (All others to GND) Vmax 7.0 V Maximum Current (UVLO<VIN<OVLO) Imax 2.0 A Thermal Resistance, Junction−to−Air (Note 1) RqJA 280 °C/W Operating Ambient Temperature Range TA −40 to +85 °C Storage Temperature Range Tstg −65 to +150 °C Junction Operating Temperature TJ 150 °C ESD Withstand Voltage (IEC 61000−4−2) (input only) when bypassed with 1.0 mF capacitor Human Body Model (HBM), Model = 2 (Note 2) Machine Model (MM) Model = B (Note 3) Vesd 15 Air, 8.0 Contact 2000 200 kV V V Moisture Sensitivity MSL Level 1 − Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. The RqJA is highly dependent on the PCB heat sink area (connected to pad 2). As example RqJA is 268 °C/W with 30 mm 2 (copper 35 mm) and 189 °C/W with 400 mm2. 2. Human Body Model, 100 pF discharged through a 1.5 k W resistor following specification JESD22/A114. 3. Machine Model, 200 pF discharged through all pins following specification JESD22/A115. |
同様の部品番号 - NCP348 |
|
同様の説明 - NCP348 |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |