GAMEWELL-FCI

12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118

9021-60292 Rev. A page 2 of 2

www.gamewell-fci.com

Options

CAC-4

Used to convert Style B (Class B) IDCs to

Style D (Class A) and Style Y (Class B)

NACs to Style Z (Class A). Mounts in

FACP. Flex 404 only.

XRM-24

Second 100VA transformer for maximum

accessory power. Mounts in FACP. Flex

404 only.

4XTMF

Transmitter module provides output for

local energy municipal box transmitter and

alarm and trouble reverse polarity. Mounts

in FACP. Flex 402 & Flex 404.

4XZMF

Zone relay module provides Form-C relays:

Alarm Zones 1, 2, 3, 4, System Alarm,

Trouble. Mounts in FACP. Flex 404 only.

4XLMF

LED interface module supports the

GWSAN-404 remote annunciator,

supervises annunciator wiring for open

conditions. Mounts in FACP. Flex 404 only.

411UD

Four input/channel, dual line, digital alarm

communicator/transmitter(DACT). Input/

channels are compatible with normally

open relay contacts, are supervised and

fully programmable. Interfaces with public

switched telephone networks and

compatible with most central station receiv-

ers. Flex 404 only.

GWSAN-404 Remote annunciator mounts in single-gang

electrical box, provides LED indication of

Alarm Zones 1, 2, 3, 4; and System

Trouble. Flex 404 only.

Specifications

AC Power

120 VAC, 50/60Hz, 2.3 A

Battery

Max. charging circuit: 27.6 VDC@ 0.8A

Max. charger capacity: 18 Ah (two 7Ah

batteries fit inside FACP)

Initiating Device Alarm zones 1 & 2 (Flex 402 / Flex 404)

Circuits (IDC)

Alarm zones 3 & 4 (Flex 404 only)

Operation: All zones Style B (Class B)

Power limited circuitry

Operating voltage: nominal 20 VDC

Alarm current: 15 mA minimum

Short circuit current: 40 mA maximum

Standby current: 4 mA

Maximum loop resistance: 100 ohms

Notification

One NAC: Flex 402; two NACs:Flex 404

Specifications (Continued)

Circuits (NAC)

Operation: Style Y (Class B)

Power limited circuitry

Operating voltage: nominal 24 VDC

Maximum signaling current: 2.5 A total

(5.0 A Flex 404 with optional

transformer)

Maximum line impedance: 1.5 volt drop

Form-C Relays Trouble, Alarm (Supervisory, Flex 404)

Contact ratings 2 A @ 30 VAC

(resistive)

Resettable

Operating voltage: nominal 24 VDC

power

Power limited circuitry

Maximum available current: 500 mA

Nonresettable

Operating voltage: nominal 24 VDC

power

Power limited circuitry

Maximum Available current: 500 mA

Cabinet

Door: 15.3" x 14.7" x 0.3"

(39 x 37 x 1 cm)

Backbox: 15.0" x 14.5" x 3.0"

(

38 x 37 x 8 cm)

Ordering Information

GWF402

Flex 402 conventional FACP, 2 zones,

120 VAC, red

GWF404

Flex 404 conventional FACP, 4 zones,

120 VAC, red

71252

EOL resistor, 4.7K ohm, ½ watt

52194

Flex 402 and Flex 404 Installation &

Operation Manual

Options:

CAC-4

Class A converter for initiating device

circuits and notification appliance cir-

cuits (cannot be used on Flex 402)

XRM-24

Transformer, expands NAC circuit

power from 3 to 5 amps

4XTMF

Transmitter module for remote station

output or municipal box connection

4XZMF

Relay module, four relays-by-zone,

alarm and trouble contacts, 24VDC

4XLMF

Remote annunciator driver, 24 VDC,

supports GWSAN-404

411UD

Four channel dual slave programmer

DACT, Form C relay and upload/down-

load capability; with enclosure, requires

PRO-411

PRO-411

Programmer, use with 411UD,

411UDAC

GWSAN-404

LED remote annunciator for Flex 404,

4 alarms, 1 trouble (requires 4XLMF)

BB-17F

Battery box, houses 2 batteries

(7-18 Ah max)