データシートサーチシステム |
|
ST40RA200XH6 データシート(PDF) 9 Page - STMicroelectronics |
|
ST40RA200XH6 データシート(HTML) 9 Page - STMicroelectronics |
9 / 94 page 4 Architecture ST40RA 9/94 STMicroelectronics ADCS 7260755H Debug controller Debugging is performed by break interrupts. There are two break channels. The address, data value, access type, and data size can all be set as break conditions. Sequential break functions are supported. The user debug interface (UDI) contains a five-pin serial interface conforming to JTAG, IEEE Standard TAP and boundary scan architecture. The interface provides host access to the 1 Kbyte ASERAM for emulator firmware (accessible only in ASE mode). Timers The three-channel, auto-reload, 32-bit timer has an input capture function and a choice of seven counter input clocks. Real-time clock The built-in 32-kHz crystal oscillator has a maximum 1/256 second resolution. It has dynamically programmable operating frequencies and on-chip clock and calendar functions. It has two sleep modes and one standby mode. Watchdog timer The ST40RA has an 8-bit watchdog timer (WDT) with programmable clock ratio. The WDT is able to generate a power-on reset or a manual reset. Programmable PLLs The ST40RA has three programmable PLLs. The PLLs are configured by MODE pins at reset and then reconfigured by software to optimize system performance or reduce system power consumption. General-purpose DMA controller The five-channel physical address GPDMA controller has four general-purpose channels for memory-to-memory or memory-to-peripheral transfers, and one buffered multiplexed channel. Both 2-D block moves and linked lists are supported. Two sets of DMA handshake pins are available for use by external devices to support efficient transfer interdevice transfers via external interfaces such as the EMI MPX. Parallel I/O module 24 bits of parallel I/O are provided from the ST40 compatible PIO. Each bit is programmable as an output or an input. “Input compare” generates an interrupt on any change of any input bit. 4.3 Bus interfaces 4.3.1 Local memory interface The LMI supports 16-, 32- and 64-bit wide bus SDRAM and DDR SDRAM, at up to 100 MHz with a maximum address space of 112 Mbytes. Devices supported include two and four bank 16-, 64-, 128- and 256-Mbit technologies in x4, x8, x16 and x32 packages. The LMI pads are dual mode pads electrically compatible with LVTTL (for standard SDRAM) and SSTL_2 (for DDR SDRAM). For full detail of the configuration options of the LMI please see ST40 System Architecture Manual, Volume 2: Bus Interfaces. |
同様の部品番号 - ST40RA200XH6 |
|
同様の説明 - ST40RA200XH6 |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |