 |
データシートサーチシステム |
|
|
データシートサーチシステム |
|
ATmega128-16AU データシート(PDF) 66 Page - ATMEL Corporation |
|
||||||||||||||||||||||||||||||
ATmega128-16AU データシート(HTML) 66 Page - ATMEL Corporation |
|
|
66 / 386 page  66 2467S–AVR–07/09 ATmega128 I/O Ports Introduction All AVR ports have true Read-Modify-Write functionality when used as general digital I/O ports. This means that the direction of one port pin can be changed without unintentionally changing the direction of any other pin with the SBI and CBI instructions. The same applies when chang- ing drive value (if configured as output) or enabling/disabling of pull-up resistors (if configured as input). Each output buffer has symmetrical drive characteristics with both high sink and source capability. The pin driver is strong enough to drive LED displays directly. All port pins have indi- vidually selectable pull-up resistors with a supply-voltage invariant resistance. All I/O pins have protection diodes to both V CC and Ground as indicated in Figure 29. Refer to “Electrical Charac- teristics” on page 318 for a complete list of parameters. Figure 29. I/O Pin Equivalent Schematic All registers and bit references in this section are written in general form. A lower case “x” repre- sents the numbering letter for the port, and a lower case “n” represents the bit number. However, when using the register or bit defines in a program, the precise form must be used. For example, PORTB3 for bit no. 3 in Port B, here documented generally as PORTxn. The physical I/O regis- ters and bit locations are listed in “Register Description for I/O Ports” on page 87. Three I/O memory address locations are allocated for each port, one each for the Data Register – PORTx, Data Direction Register – DDRx, and the Port Input Pins – PINx. The Port Input Pins I/O location is read only, while the Data Register and the Data Direction Register are read/write. In addition, the Pull-up Disable – PUD bit in SFIOR disables the pull-up function for all pins in all ports when set. Using the I/O port as General Digital I/O is described in “Ports as General Digital I/O” on page 67. Most port pins are multiplexed with alternate functions for the peripheral features on the device. How each alternate function interferes with the port pin is described in “Alternate Port Functions” on page 71. Refer to the individual module sections for a full description of the alter- nate functions. Note that enabling the alternate function of some of the port pins does not affect the use of the other pins in the port as General Digital I/O. C PIN Logic R PU See Figure "General Digital I/O" for Details Pxn |
同様の部品番号 - ATmega128-16AU |
|
同様の説明 - ATmega128-16AU |
|
|
リンク URL |
| プライバシーポリシー |
| ALLDATASHEET.JP |
| ALLDATASHEETはお客様のビジネスに役立ちますか？ [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Japanese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
