データシートサーチシステム |
|
ISL23315TFRUZ-T7A データシート(PDF) 8 Page - Intersil Corporation |
|
ISL23315TFRUZ-T7A データシート(HTML) 8 Page - Intersil Corporation |
8 / 19 page ISL23315 8 FN7778.0 December 15, 2010 DCP Macro Model tSU:STO STOP Condition Set-up Time From SCL rising edge crossing 70% of VLOGIC, to SDA rising edge crossing 30% of VLOGIC 600 ns tHD:STO STOP Condition Hold Time for Read or Write From SDA rising edge to SCL falling edge; both crossing 70% of VCC (Note 11) 1300 ns tDH Output Data Hold Time From SCL falling edge crossing 30% of VLOGIC, until SDA enters the 30% to 70% of VLOGIC window. IOL =3mA, VLOGIC > 2V. IOL = 0.5mA, VLOGIC < 2V 0ns tR SDA and SCL Rise Time From 30% to 70% of VLOGIC 20 + 0.1 x Cb 250 ns tF SDA and SCL Fall Time From 70% to 30% of VLOGIC 20 + 0.1 x Cb 250 ns Cb Capacitive Loading of SDA or SCL Total on-chip and off-chip (Note 11) 10 400 pF tSU:A A1, A0 setup time Before START condition 600 ns tHD:A A1, A0 hold time After STOP condition 600 ns NOTES: 8. Typical values are for TA = +25°C and 3.3V supply voltages. 9. LSB = [V(RW)255 – V(RW)0]/255. V(RW)255 and V(RW)0 are V(RW) for the DCP register set to FF hex and 00 hex respectively. LSB is the incremental voltage when changing from one tap to an adjacent tap. 10. ZS error = V(RW)0/LSB. 11. FS error = [V(RW)255 – VCC]/LSB. 12. DNL = [V(RW)i – V(RW)i-1]/LSB-1, for i = 1 to 255. i is the DCP register setting. 13. INL = [V(RW)i – i • LSB – V(RW)0]/LSB for i = 1 to 255 14. for i = 16 to 255 decimal, T = -40°C to +125°C. Max( ) is the maximum value of the wiper voltage and Min( ) is the minimum value of the wiper voltage over the temperature range. 15. MI = |RW255 – RW0|/255. MI is a minimum increment. RW255 and RW0 are the measured resistances for the DCP register set to FF hex and 00 hex respectively. 16. Roffset = RW0/MI, when measuring between RW and RL. Roffset = RW255/MI, when measuring between RW and RH. 17. RDNL = (RWi – RWi-1)/MI -1, for i = 16 to 255. 18. RINL = [RWi – (MI • i) – RW0]/MI, for i = 16 to 255. 19. for i = 16 to 255, T = -40°C to +125°C. Max( ) is the maximum value of the resistance and Min( ) is the minimum value of the resistance over the temperature range. 20. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. 21. It is preferable to ramp up both the VLOGIC and the VCC supplies at the same time. If this is not possible it is recommended to ramp-up the VLOGIC first followed by the VCC. Serial Interface Specification for SCL, SDA, A0, A1 Unless Otherwise Noted. (Continued) SYMBOL PARAMETER TEST CONDITIONS MIN (Note 20) TYP (Note 8) MAX (Note 20) UNITS TCV Max V RW ()i () Min V RW ()i () – VRWi +25°C () () ------------------------------------------------------------------------------ 106 +165°C --------------------- × = TCR Max Ri () Min Ri () – [] Ri +25°C () ------------------------------------------------------- 10 6 +165°C --------------------- × = 22pF RH RTOTAL CH 32pF CW CL 22pF RW RL |
同様の部品番号 - ISL23315TFRUZ-T7A |
|
同様の説明 - ISL23315TFRUZ-T7A |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |