データシートサーチシステム |
|
D-300-03 データシート(PDF) 7 Page - PANDUIT CORP. |
|
D-300-03 データシート(HTML) 7 Page - PANDUIT CORP. |
7 / 7 page SPECIFICATION CONTROL DRAWING 307 Constitution Drive Menlo Park, CA 94025, USA Wire and Harnessing Products TITLE : CAP, SPLICE ENCAPSULATION UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS. INCHES DIMENSIONS ARE BETWEEN BRACKETS. DOCUMENT NO.: D-300-01/-03 TOLERANCES: 0.00 N/A 0.0 N/A 0 N/A ANGLES: N/A ROUGHNESS IN MICRON Tyco Electronics reserves the right to amend this drawing at any time. Users should evaluate the suitability of the product for their application. DCR NUMBER: D010043 REPLACES: N/A DRAWN BY: M. FORONDA DATE: 15-Feb.-01 PROD. REV. SEE TABLE DOC ISSUE: 1 SCALE: None SIZE: A SHEET: 7 of 7 If this document is printed it becomes uncontrolled. Check for the latest revision. Thermofit Assembly Procedure 1. Strip the wires and install crimp type connector or solder wires together. Connector should be installed so that 1/6 ± 1/32 of conductor is exposed between the connector and the wire insulation, as shown in Figure 1. 2. Choose the proper size cap from the chart below. Place splice into cap so that the connector bottoms on the rounded end of the cap. 3. Heat the assembly, using a Thermogun, Model 500A, or equivalent, equipped with a TG-12 or TG-13A reflector. 4. The average length of time required for proper heating is given in the chart. However, since the heat sink effect of various wire bundles may vary considerably, several trial specimens should be crossed-sectioned as shown in Figure 2 before proceeding with production installations. If the area between the wires is not completely filled, a longer heating cycle should be established. 5. With wire bundles of more than three wires, it is helpful to slightly deform the cap by pinching in the area above the connection at the end of the heating cycle and then returning the cap to the heat for an additional period to allow the cap to return to its cylindrical shape. Chart 1 Part Splicer Diameter Time Bundle Diameter Name Minimum Maximum (sec.) Maximum D-300-01 2.03 (0.080) 4.91 (0.165) 30 .115 D-300-02 3.04 (0.120) 6.35 (0.250) 45 .200 D-300-03 4.57 (0.180) 8.89 (0.350) 60 .300 Figure 1 Figure 2 |
同様の部品番号 - D-300-03 |
|
同様の説明 - D-300-03 |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |