5-24

FAST AND LS TTL DATA

MIN

MIN

MAX

MAX

MILLIMETERS

INCHES

DIM

A

B

C

D

F

G

J

K

M

P

R

8.55

3.80

1.35

0.35

0.40

0.19

0.10

0°

5.80

0.25

8.75

4.00

1.75

0.49

1.25

0.25

0.25

7°

6.20

0.50

0.337

0.150

0.054

0.014

0.016

0.008

0.004

0°

0.229

0.010

0.344

0.157

0.068

0.019

0.049

0.009

0.009

7°

0.244

0.019

1.27 BSC

0.050 BSC

NOTES:

1. DIMENSIONS A" AND B" ARE DATUMS AND

T" IS A DATUM SURFACE.

2. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

3. CONTROLLING DIMENSION: MILLIMETER.

4. DIMENSION A AND B DO NOT INCLUDE MOLD

PROTRUSION.

5. MAXIMUM MOLD PROTRUSION 0.15 (0.006)

PER SIDE.

6. 751A01 IS OBSOLETE, NEW STANDARD

751A02.

-A-

-B-

P

G

C

K

SEATING

PLANE

14 PL

D

M

F

J

7 PL

R X 45

°

1

7

8

14

Case 751A-02 D Suffix

14-Pin Plastic

SO-14

B

M

T

0.25 (0.010)

B

A

M

S

S

Case 632-08 J Suffix

14-Pin Ceramic Dual In-Line

MIN

MIN

MAX

MAX

MILLIMETERS

INCHES

DIM

A

B

C

D

F

G

J

K

L

M

N

19.05

6.23

3.94

0.39

1.40

0.21

3.18

0°

0.51

19.94

7.11

5.08

0.50

1.65

0.38

4.31

15°

1.01

0.750

0.245

0.155

0.015

0.055

0.008

0.125

0°

0.020

0.785

0.280

0.200

0.020

0.065

0.015

0.170

15°

0.040

2.54 BSC

7.62 BSC

0.100 BSC

0.300 BSC

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION L TO CENTER OF LEAD WHEN

FORMED PARALLEL.

4. DIM F MAY NARROW TO 0.76 (0.030) WHERE

THE LEAD ENTERS THE CERAMIC BODY.

5. 63201 THRU 07 OBSOLETE, NEW STANDARD

63208.

14

8

1

7

-A-

-B-

-T-

SEATING

PLANE

F

G

D

14 PL

N

K

C

L

J

14 PL

M

0.25 (0.010)

T A

M

S

0.25 (0.010)

T B

M

S

Case 646-06 N Suffix

14-Pin Plastic

MIN

MIN

MAX

MAX

MILLIMETERS

INCHES

DIM

18.16

6.10

3.69

0.38

1.02

1.32

0.20

2.92

19.56

6.60

4.69

0.53

1.78

2.41

0.38

3.43

0°

0.39

0.715

0.240

0.145

0.015

0.040

0.052

0.008

0.115

0.770

0.260

0.185

0.021

0.070

0.095

0.015

0.135

10°

1.01

2.54 BSC

7.62 BSC

0.100 BSC

0.300 BSC

0°

0.015

10°

0.039

A

B

C

D

F

G

H

J

K

L

M

N

NOTES:

1. LEADS WITHIN 0.13 mm (0.005) RADIUS OF TRUE

POSITION AT SEATING PLANE AT MAXIMUM

MATERIAL CONDITION.

2. DIMENSION L" TO CENTER OF LEADS WHEN

FORMED PARALLEL.

3. DIMENSION B" DOES NOT INCLUDE MOLD

FLASH.

4. ROUNDED CORNERS OPTIONAL.

5. 64605 OBSOLETE, NEW STANDARD 64606.

1

7

14

8

B

A

NOTE 4

F

H

G

D

SEATING

PLANE

N

K

C

L

J

M