データシートサーチシステム |
|
I2013RU データシート(PDF) 2 Page - MicroPower Direct, LLC |
|
I2013RU データシート(HTML) 2 Page - MicroPower Direct, LLC |
2 / 2 page Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) Model Number Input Output Efficiency (%, Typ) Capacitive Load (µF Max) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min) Nominal Range Full-Load No-Load I2001RU 24 9.0 - 36.0 1,390 80 3.3 4,500 0 87 10,300 4,000 I2002RU 24 9.0 - 36.0 1,852 90 5.0 4,000 0 89 6,800 4,000 I2003RU 24 9.0 - 36.0 1,877 40 12.0 1,670 0 89 1,200 4,000 I2004RU 24 9.0 - 36.0 1,882 40 15.0 1,340 0 89 750 4,000 I2005RU 24 9.0 - 36.0 1,877 40 ±12.0 ±835 ±60 89 ±680 4,000 I2006RU 24 9.0 - 36.0 1,882 40 ±15.0 ±670 ±50 89 ±380 4,000 I2011RU 48 18.0 - 75.0 695 40 3.3 4,500 0 88 10,300 2,000 I2012RU 48 18.0 - 75.0 926 45 5.0 4,000 0 89 6,800 2,000 I2013RU 48 18.0 - 75.0 938 25 12.0 1,670 0 89 1,200 2,000 I2014RU 48 18.0 - 75.0 930 25 15.0 1,340 0 89 750 2,000 I2015RU 48 18.0 - 75.0 938 25 ±12.0 ±835 ±60 89 ±680 2,000 I2016RU 48 18.0 - 75.0 941 25 ±15.0 ±670 ±50 89 ±380 2,000 Derating Curve Notes: 1. Output ripple is measured with a 1.0 µF ceramic and a 10 µF tantalum capcitor connected across the outputs. 2. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%. 3. Operation at no-load will not damage the unit, but they may not meet all specifications. 4. The On/Off Control input (Pin 3) is referenced to -Vin (Pin 2). If it is not used, the control pin should be left open. If the pin is shorted to -VIN, the unit will turn off. 5. An external resistor may be used to adjust the converter output by ±10%.To adjust the output UP, connect a 5%, 3W resistor between the minus output pin and the Vout trim pin. To adjust the output DOWN, connect a 5%, 3W resistor between the plus output pin and the V OUT trim pin. For continuous UP/Down trimming capability, connect a 10 kW potentiometer between the plus and minus outputs with the wiper arm connected to the V OUT trim pin.The trim pin may be left floating if it is not used. Contact the factroy for more information. 6. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. www.micropowerdirect.com Pin Single Dual 1 +Vin +Vin 2 -Vin -Vin 3 Remote ON/OFF 4 +Vout +Vout 5 Trim Common 6 -Vout -Vout Pin Connections Model Selection Guide Mechanical Dimensions MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com Min Max On 3.5 VDC 12 VDC Off 0.0 VDC 1.2 VDC In. Current (on) 0.5 mA In. Current (off) -0.5 mA |
同様の部品番号 - I2013RU |
|
同様の説明 - I2013RU |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |