データシートサーチシステム |
|
TS201 データシート(PDF) 2 Page - MORNSUN Science& Technology Ltd. |
|
TS201 データシート(HTML) 2 Page - MORNSUN Science& Technology Ltd. |
2 / 3 page The copyright and authority for the interpretation of the products are reserved by MORNSUN TSX01-EX 2013.07.01-A/4 Page 2 of 3 ISOLATION SPECIFICATIONS Five-port isolation Output ~ Input: 2.5KVAC Power Supply ~ Input: 2.5KVAC Power Supply ~ Output: 1.5KVAC Output 1 ~ Output 2: 1.5KVAC Input 1 ~ Input 2: 1.5VAC Electrical isolation Three-port isolation (Single channel); Five-port isolation(Dual channels) Isolation strength 2.5KVAC (test for 1minute, humidity < 70%) EMC EN61326 STANDARDS & CERTIFICATES Explosion protection Certificate mark [Exia]IIC Explosion protection certificate param eters Between the pin 11 and 12: Um=250VAC/DC Uo=10.5VDC Io=5.3mA Po=14mW Co=1.68 µF Lo=1000mH Explosion protection certificate agency CHINA NATIONAL QUALITY SUPERVISION AND TEST CENTRE FOR EXPLOSION PROTECTED ELECTRICAL PRODUCTS Explosion qualified NO. CNEx08.0003 OTHER SPECIFICATIONS Operation temperature:-25 °C ~ +71°C Ambient temperature Transport and Storage temperature:-50 °C ~ +105°C Mounting 35mm DIN-rail package, hot plug, thickness: 22.5mm, Plastic UL94-V0 Safety Grade IP20(IEC60529 / EN60529) Weight About 128g CONNECTION In intrinsic safety explosion protection systems, isolating barrier belongs to affiliated device. It is installed at safe area, as a connection between intrinsic safety devices in the hazardous area and non-intrinsic safety devices in the safe area. By limiting the energy to a certain safe am ount, it ensures the safety of in spot devices and people. Selection regulations for intrinsic safety explosion protection system: 1.The explosion protection grade of the barrier must be equal to or higher than that of in spot intrinsic safety explosion protection device. 2.Take inconsideration of hazardous end output resistance and loop resistance, ake sure the barrier ’s output voltage meets the minimum operation voltage requirement of in spot intrinsic safety device. 3.The safety parameters of Barrier ’s intrinsic safety end meets: Uo ≤ UI, Io ≤ Iin, Po ≤ Pin Co ≥ Cin, Lo ≥ Lin 4.Select suitable Safety barrier which matches the in spot intrinsic safety device for the power ’s phase, signal type and transmission mode. 5.Apply necessary protections, avoid influence the in spot intrinsic safety device ’s operation from leakage current that generated by safety barrier. Operation notes: 1. Please read the user manual carefully before using. If any questions please contact our technical support department. 2. Please do not use this product in hazardous area. 3. The power supply of this product should be 24VDC power source. It is forbidden to use 220VAC power supply. 4. To avoid invalid explosion protection function, or any failure, users disassemble this product is forbidden. APPLICATION CIRCUIT DIAGRAM & PIN DESCRIPTION 5 Power 6 1 6 1 5 8 7 Safe area Hazardous area 1 2 1 1 4 3 Channel1 Channel2 DCS PLC Note:In single model channel2 is invaid Transistor output mode and connections (safe area): P assive pulse RL=2 20K ~ Ω V CC VCC Transistor collector output Transistor Emitter output Passive pulse RL=2 20K ~ Ω |
同様の部品番号 - TS201 |
|
同様の説明 - TS201 |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |