データシートサーチシステム |
|
ML4771ES データシート(PDF) 7 Page - Micro Linear Corporation |
|
ML4771ES データシート(HTML) 7 Page - Micro Linear Corporation |
7 / 8 page 7 ML4771 INPUT CAPACITOR Due to the high input current drawn at startup and possibly during operation, it is recommended to decouple the input with a capacitor with a value of 47µF to 100µF. This filtering prevents the input ripple from affecting the ML4771 control circuitry, and also improves the efficiency by reducing the I squared R losses during the charge cycle of the inductor. Again, a low ESR capacitor (such as tantalum) is recommended. It is also recommended that low source impedance batteries be used. Otherwise, the voltage drop across the source impedance during high input current situations will cause the ML4771 to fail to start-up or to operate unreliably. In general, for two cell applications the source impedance should be less than 200m W, which means that small alkaline cells should be avoided. SETTING THE OUTPUT VOLTAGE The adjustable output of the ML4771 requires an external feedback resistor divider to set VOUT. The output voltage can be determined from the following equation: V RR R OUT = + 257 12 2 . 16 (3) where R1 and R2 are connected as shown in Figure 2. The value of R2 should be 250k W or less to minimize bias current errors. Choose an appropriate value for R2 and calculate R1. LAYOUT Good layout practices will ensure the proper operation of the ML4771. Some layout guidelines follow: • Use adequate ground and power traces or planes • Keep components as close as possible to the ML4771 • Use short trace lengths from the inductor to the VL1 and VL2 pins and from the output capacitor to the VOUT pin • Use a single point ground for the ML4771 ground pin, and the input and output capacitors • Separate the ground for the converter circuitry from the ground of the load circuitry and connect at a single point A sample layout is shown in Figure 7. DESIGN CONSIDERATIONS (Continued) DESIGN EXAMPLE In order to design a boost converter using the ML4871, it is necessary to define a few parameters. For this example, assume that VIN = 3.0V to 3.6V, VOUT = 5.0V, and IOUT(MAX) = 500mA. First, it must be determined whether the ML4871 is capable of delivering the output current. This is done using Equation 1: I V V AA OUT MAX () . . . .. = = 125 30 50 07 0 53 Next, select an inductor. As previously mentioned, the recommended inductance is 10µH. Make sure that the peak current rating of the inductor is at least 1.5A, and that the DC resistance of the inductor is in the range of 50 to 100m W. Then, the value of the output capacitor is determined using Equation 2: C H V F OUT = = 44 10 50 88 m m . The closest standard value would be a 100µF capacitor with an ESR rating of 100m W. If such a low ESR value cannot be found, two 47µF capacitors in parallel could also be used. Finally, the values of R1 and R2 are calculated using equation 3, assuming that R2 = 250k W: Rk k k 1 50 257 250 250 236 = -= . . WW W The complete circuit is shown in Figure 8. As mentioned previously, the use of an input supply bypass capacitor is highly recommended. Figure 8. Typical Application Circuit ML4771 100µF 100µF VIN 10µH (Sumida CD75) VL1 VIN GND SENSE PWR GND NC VL2 VOUT 250k Ω 236k Ω VOUT |
同様の部品番号 - ML4771ES |
|
同様の説明 - ML4771ES |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |