データシートサーチシステム |
|
TLP7920 データシート(PDF) 3 Page - Toshiba Semiconductor |
|
TLP7920 データシート(HTML) 3 Page - Toshiba Semiconductor |
3 / 11 page TLP7920,TLP7920F 3 8. 8. 8. 8. Absolute Maximum Ratings (Note) (Unless otherwise specified, T Absolute Maximum Ratings (Note) (Unless otherwise specified, T Absolute Maximum Ratings (Note) (Unless otherwise specified, T Absolute Maximum Ratings (Note) (Unless otherwise specified, Taaaa = 25 = 25 = 25 = 25 )))) Characteristics Supply Voltages Steady-state input voltages Two-second transient input voltages Output voltages Operating temperature Storage temperature Lead soldering temperature Isolation voltage (10 s) AC, 60 s, R.H. ≤ 60 % Symbol VDD1, VDD2 VIN+, VIN- VIN+, VIN- VOUT+, VOUT- Topr Tstg Tsol BVS Note (Note 1) (Note 2) Rating -0.5 to 6 -0.5 to 6 -6 to 6 -0.5 to 6 -40 to 105 -55 to 125 260 5000 Unit V Vrms Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note: Ceramic capacitors (0.1 µF) should be connected between 1 and 4 pins and between 5 and 8 pins to stabilize the operation. Otherwise, this photocoupler may not switch properly. The bypass capacitors should be placed as close as possible to each pin. Note 1: ≥ 2 mm below seating plane. Note 2: This device is considered as a two-terminal device: Pins 1, 2, 3 and 4 are shorted together, and pins 5, 6, 7 and 8 are shorted together. 9. 9. 9. 9. Recommended Operating Conditions (Note) Recommended Operating Conditions (Note) Recommended Operating Conditions (Note) Recommended Operating Conditions (Note) Characteristics Input side supply voltage Output side supply voltage Analog input voltage Ambient temperature Symbol VDD1 VDD2 VIN+, VIN- Ta Note (Note 1), (Note 2) Min 4.5 3.0 -200 -40 Typ. 5 Max 5.5 5.5 200 105 Unit V mV Note: The recommended operating conditions are given as a design guide necessary to obtain the intended performance of the device. Each parameter is an independent value. When creating a system design using this device, the electrical characteristics specified in this datasheet should also be considered. Note 1: FSR = ±300 mV Note 2: When either VIN+ or VIN- or both are equal to or greater than VDD1 - 2 V (e.g., if VDD1 = 5 V, when VIN+ and/or VIN- are equal to or greater than 5 V - 2 V = 3 V), isolation amplifiers go into one of the test modes. Do not raise either VIN+ or VIN- above this voltage to keep the device in functional mode. 2015-09-10 Rev.1.0 ©2015 Toshiba Corporation |
同様の部品番号 - TLP7920 |
|
同様の説明 - TLP7920 |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |