データシートサーチシステム
Selected language   Japanese  ▼
品番検索
         詳細検索


MC1496 データシート(Datasheet) 4 Page - ON Semiconductor

部品番号. MC1496
部品情報  BALANCED MODULATORS/DEMODULATORS
ダウンロード  14 Pages
Scroll/Zoom Zoom In 100% Zoom Out
メーカー  ONSEMI [ON Semiconductor]
ホームページ  http://www.onsemi.com
Logo 

 
 4 page
background image
MC1496, MC1496B
http://onsemi.com
4
GENERAL OPERATING INFORMATION
Carrier Feedthrough
Carrier feedthrough is defined as the output voltage at
carrier
frequency
with
only
the
carrier
applied
(signal voltage = 0).
Carrier null is achieved by balancing the currents in the
differential amplifier by means of a bias trim potentiometer
(R1 of Figure 5).
Carrier Suppression
Carrier suppression is defined as the ratio of each
sideband output to carrier output for the carrier and signal
voltage levels specified.
Carrier suppression is very dependent on carrier input
level, as shown in Figure 22. A low value of the carrier does
not fully switch the upper switching devices, and results in
lower signal gain, hence lower carrier suppression. A higher
than optimum carrier level results in unnecessary device and
circuit carrier feedthrough, which again degenerates the
suppression figure. The MC1496 has been characterized
with a 60 mVrms sinewave carrier input signal. This level
provides optimum carrier suppression at carrier frequencies
in the vicinity of 500 kHz, and is generally recommended for
balanced modulator applications.
Carrier feedthrough is independent of signal level, VS.
Thus carrier suppression can be maximized by operating
with large signal levels. However, a linear operating mode
must be maintained in the signal−input transistor pair − or
harmonics of the modulating signal will be generated and
appear in the device output as spurious sidebands of the
suppressed carrier. This requirement places an upper limit
on input−signal amplitude (see Figure 20). Note also that an
optimum carrier level is recommended in Figure 22 for good
carrier suppression and minimum spurious sideband
generation.
At higher frequencies circuit layout is very important in
order to minimize carrier feedthrough. Shielding may be
necessary in order to prevent capacitive coupling between
the carrier input leads and the output leads.
Signal Gain and Maximum Input Level
Signal gain (single−ended) at low frequencies is defined
as the voltage gain,
A
VS +
Vo
V
S
+
R
L
Re)2re
where re +
26 mV
I5(mA)
A constant dc potential is applied to the carrier input
terminals to fully switch two of the upper transistors “on”
and two transistors “off” (VC = 0.5 Vdc). This in effect
forms a cascode differential amplifier.
Linear operation requires that the signal input be below a
critical value determined by RE and the bias current I5.
VS p I5 RE (Volts peak)
Note that in the test circuit of Figure 10, VS corresponds to
a maximum value of 1.0 V peak.
Common Mode Swing
The common−mode swing is the voltage which may be
applied to both bases of the signal differential amplifier,
without saturating the current sources or without saturating
the differential amplifier itself by swinging it into the upper
switching devices. This swing is variable depending on the
particular circuit and biasing conditions chosen.
Power Dissipation
Power dissipation, PD, within the integrated circuit
package should be calculated as the summation of the
voltage−current products at each port, i.e. assuming
V12 = V6, I5 = I6 = I12 and ignoring base current,
PD = 2 I5 (V6 − V14) + I5)V5 − V14 where subscripts refer
to pin numbers.
Design Equations
The following is a partial list of design equations needed
to operate the circuit with other supply voltages and input
conditions.
A. Operating Current
The internal bias currents are set by the conditions at Pin 5.
Assume:
I5 = I6 = I12,
IB
ttIC for all transistors
then :
R5
+
V
**f
I5
*500 W
where: R5 is the resistor between
where: Pin 5 and ground
where:
f = 0.75 at TA = +25°C
The MC1496 has been characterized for the condition
I5 = 1.0 mA and is the generally recommended value.
B. Common−Mode Quiescent Output Voltage
V6 = V12 = V+ − I5 RL
Biasing
The MC1496 requires three dc bias voltage levels which
must be set externally. Guidelines for setting up these three
levels include maintaining at least 2.0 V collector−base bias
on all transistors while not exceeding the voltages given in
the absolute maximum rating table;
30 Vdc
w [(V6, V12) − (V8, V10)] w 2 Vdc
30 Vdc
w [(V8, V10) − (V1, V4)] w 2.7 Vdc
30 Vdc
w [(V1, V4) − (V5)] w 2.7 Vdc
The foregoing conditions are based on the following
approximations:
V6 = V12, V8 = V10, V1 = V4




Html ページ

1  2  3  4  5  6  7  8  9  10  11  12  13  14 


Datasheet Download



関連電子部品番号

部品番号コンポーネントの説明Html Viewメーカー
AM028D1-0026-33 GHz GaAs MMIC Double Balanced Down Converter Mixer 1 2 Alpha Industries
HSM276SRSilicon Schottky Barrier Diode for Balanced Mixer 1 2 3 4 5 Hitachi Semiconductor
MA4EX180M-1225Silicon Double Balanced HMICTM Mixer 1300 - 1900 MHz 1 2 3 4 Tyco Electronics
TUA60202 Band TV Tuner Mixer-Oscillator-PLL with balanced IF-Amplifier 1 2 3 4 5 MoreInfineon Technologies AG
U2796B2-GHz Single Balanced Mixer 1 2 3 4 5 MoreTEMIC Semiconductors
SPM5001RF Double Balanced Mixer 1 2 3 Sanyo Semicon Device
TL442MBalanced mixers 1 2 3 4 5 MoreTI store
AM028D1-A226-33 GHz Surface Mount Double Balanced Down Converter Mixer 1 2 3 4 Alpha Industries
HSM88ASSilicon Schottky Barrier Diode for Balanced Mixer 1 2 3 4 5 Hitachi Semiconductor
MA4EX190H-1225Silicon Double Balanced HMICTM Mixer 1700 - 2300 MHz 1 2 3 Tyco Electronics

リンク URL

ALLDATASHEETはお客様のビジネスに役立ちますか?  [ DONATE ]  

Alldatasheetは   |   広告   |   お問い合わせ   |   プライバシーポリシー   |   ブックマーク   |   リンク交換   |   メーカーリスト
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  , Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp  |   Russian : Alldatasheetru.com
Korean : Alldatasheet.co.kr   |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com  |   Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl