データシートサーチシステム |
|
BM63373S-VA データシート(PDF) 4 Page - Rohm |
|
BM63373S-VA データシート(HTML) 4 Page - Rohm |
4 / 24 page 4/21 BM63373S-VA BM63373S-VC TSQ50501-BM63373S-2 © 2020 ROHM Co., Ltd. All rights reserved. 30.Jul.2020 Rev.001 www.rohm.com TSZ22111・15・001 Absolute Maximum Ratings (Unless otherwise specified, Tj=25°C) Inverter Part Item Symbol Ratings Unit Conditions Supply Voltage VP 450 V Applied between P-NU,NV,NW Supply Voltage(Surge) VP(surge) 500 V Applied between P-NU,NV,NW Collector-Emitter Voltage VCES 600 V Collector Current DC IC ±10 (Note 1) A TC=25°C PEAK ICP ±30 (Note 1) A TC=25°C, less than 1ms Collector Power Dissipation PC 33 W TC=25°C, per 1 chip Junction Temperature Tjmax 150 °C (Note 1) Do not, however exceed PC, ASO. Control part Item Symbol Ratings Unit Conditions Control Power Supply VCC 20 V Applied between HVCC-GND, LVCC-GND Floating Control Power Supply VBS 20 V Applied between VBU-U, VBV-V, VBW-W Control Input Voltage VIN -0.5 to VCC +0.5 V Applied between HINX, LINX-GND (X=U,V,W) Fault Output Supply Voltage VFO -0.5 to VCC +0.5 V Applied between FO-GND Fault Output Current IFO 1 mA Sink current at FO pin Current Sensing Input Voltage VCIN -0.5 to +7.0 V Applied between CIN-GND Temperature Output Voltage VOT -0.5 to +7.0 V Applied between VOT-GND Bootstrap diode part Item Symbol Ratings Unit Conditions Reverse Voltage VRB 600 V Junction Temperature TjmaxD 150 °C Total system Item Symbol Ratings Unit Conditions Self Protection Supply Voltage (SCP Capability) VP(PROT) 400 V VCC=13.5 to 16.5V, Inverter part Tj=125°C, non-repetitive, less than 2µs Module Case Temperature TC -25 to +115 °C Measurement point of TC is provided in Figure 2 Storage Temperature Tstg -40 to +125 °C Isolation Voltage Viso 1500 Vrms Sinusoidal, 60Hz, AC 1min, between connected all pins and heat sink plate Thermal resistance Item Symbol Limit Unit Conditions Min Typ Max Junction to Case Thermal Resistance (Note 2) Rth(j-c)_IGBT - - 3.7 °C /W Inverter IGBT(1/6 module) Rth(j-c)_FWD - - 4.5 °C /W Inverter FWD(1/6 module) (Note 2) Grease with good conductivity and high reliability should be applied evenly with +100 to +200µm on the contacting surface of IPM and heat sink. Use a torque wrench to fasten up to the specified torque rating. The contacting thermal resistance between IPM case and heat sink is determined by the thickness and the thermal conductivity of the applied grease. Caution: Operating the IPM over the absolute maximum ratings may damage the IPM. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IPM is operated over the absolute maximum ratings. |
同様の部品番号 - BM63373S-VA |
|
同様の説明 - BM63373S-VA |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |