データシートサーチシステム |
|
MC74HC4316A データシート(PDF) 3 Page - ON Semiconductor |
|
MC74HC4316A データシート(HTML) 3 Page - ON Semiconductor |
3 / 12 page MC74HC4316A http://onsemi.com 3 MAXIMUM RATINGS Symbol Parameter Value Unit VCC Positive DC Supply Voltage (Ref. to GND) (Ref. to VEE) – 0.5 to + 7.0 – 0.5 to + 14.0 V VEE Negative DC Supply Voltage (Ref. to GND) – 7.0 to + 0.5 V VIS Analog Input Voltage VEE – 0.5 to VCC + 0.5 V Vin DC Input Voltage (Ref. to GND) – 0.5 to VCC + 0.5 V I DC Current Into or Out of Any Pin ± 25 mA PD Power Dissipation in Still Air Plastic DIP* EIAJ/SOIC Package* TSSOP Package* 750 500 450 mW Tstg Storage Temperature – 65 to + 150 °C TL Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP, SOIC or TSSOP Package) 260 °C Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. *Derating − Plastic DIP: – 10 mW/ °C from 65° to 125°C EIAJ/SOIC Package: – 7 mW/ °C from 65° to 125°C TSSOP Package: − 6.1 mW/ °C from 65° to 125°C For high frequency or heavy load considerations, see Chapter 2 of the ON Semiconductor High−Speed CMOS Data Book (DL129/D). RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit VCC Positive DC Supply Voltage (Ref. to GND) 2.0 6.0 V VEE Negative DC Supply Voltage (Ref. to GND) – 6.0 GND V VIS Analog Input Voltage VEE VCC V Vin Digital Input Voltage (Ref. to GND) GND VCC V VIO* Static or Dynamic Voltage Across Switch − 1.2 V TA Operating Temperature, All Package Types – 55 + 125 °C tr, tf Input Rise and Fall Time VCC = 2.0 V (Control or Enable Inputs) VCC = 3.0 V (Figure 10) VCC = 4.5 V VCC = 6.0 V 0 0 0 0 1000 600 500 400 ns *For voltage drops across the switch greater than 1.2 V (switch on), excessive VCC current may be drawn; i.e., the current out of the switch may contain both VCC and switch input components. The reliability of the device will be unaffected unless the Maximum Ratings are exceeded. This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high−impedance cir- cuit. For proper operation, Vin and Vout should be constrained to the range GND v (Vin or Vout) v VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. I/O pins must be connected to a properly terminated line or bus. |
同様の部品番号 - MC74HC4316A |
|
同様の説明 - MC74HC4316A |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |