データシートサーチシステム |
|
LM111 データシート(PDF) 3 Page - NXP Semiconductors |
|
LM111 データシート(HTML) 3 Page - NXP Semiconductors |
3 / 4 page Philips Semiconductors Linear Products Product specification LM111/211/311/ LM311B Voltage comparator August 31, 1994 275 DC ELECTRICAL CHARACTERISTICS1, 2, 3, 6 Over temperature range unless otherwise specified. SYMBOL PARAMETER TEST CONDITIONS LM111/LM211 LM311 LM311B UNIT SYMBOL PARAMETER TEST CONDITIONS Min Typ Max Min Typ Max Min Typ Max UNIT VOS Input offset voltage3 TA=25°C, RS≤50kΩ 0.7 3.0 2.0 7.5 2.0 7.5 mV IOS Input offset current3 TA=25°C 4.0 10 6.0 50 6 25 nA IBIAS Input bias current TA=25°C 60 100 100 250 100 200 nA AV Voltage gain TA=25°C 200 200 200 V/mV Response time4 TA=25°C 200 200 500 ns VSAT Saturation voltage LM111/211 VIN≤-5mV, IOUT=50mA LM311/B VIN≤-10mV, IOUT=50mA TA=25°C 0.75 1.5 0.75 1.5 0.75 1.5 V IBAL/STR Strobe on current TA=25°C 3.0 3.0 3.0 mA ILEAKAGE Output leakage current6 LM111/211 VIN≥5mV, VOUT=35V LM311/B VIN≥10mV, VOUT=35V TA=25°C, ISTROBE=3mA (V– = VGND = –5V) 0.2 10 0.2 50 0.2 50 nA VOS Input offset voltage3 RS≤50kΩ 4.0 10 10 mV IOS Input offset current3 20 70 50 nA IBIAS Input bias current 150 300 250 nA VIN Input voltage range V= ±15V (Pin 7 may go to 5V) -14.5 13.8 to -14.7 13.0 -14.5 13.8 to -14.7 13.0 V– +0.5 V+ –1.5 V VOL Saturation voltage6 V+ ≥ 4.5V, V- = 0 LM111/211 VIN≤-6mV, ISINK≤8mA LM311/B VIN≤-10mV, ISINK≤8mA 0.23 0.4 0.23 0.4 0.23 0.4 V IOH Output leakage current VIN≥5mV, VOUT=35V 0.1 0.5 µA ICC Positive supply current TA=25°C 5.1 6.0 5.1 7.5 1.6 3.5 mA IEE Negative supply voltage TA=25°C 4.1 5.0 4.1 5.0 mA NOTES: 1. This rating applies for ±15V supplies. The positive input voltage limit is 30V above the negative supply. The negative input voltage limit is equal to the negative supply voltage or 30V below the positive supply, whichever is less. 2. These specifications apply for VS=±15V and 0°C < TA < 70°C unless otherwise specified. With the LM211, however, all temperature specifications are limited to -25 °C ≤ TA ≤ 85°C and for the LM111 is limited to -55°C TA < 125°C. The offset voltage, offset current, and bias current specifications apply for any supply voltage from a single 5V supply up to ±15V supplies. 3. The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with 1mA load. Thus, these parameters define an error band and take into account the worst case effects of voltage gain and input impedance. 4. The response time specified is for a 100mV input step with 5mV over-drive. 5. Do not short the strobe pin to ground; it should be current driven at 3mA to 5mA. 6. LM311B, all parameters are at V+ = 3V ±10%, V– = GND = 0V. |
同様の部品番号 - LM111 |
|
同様の説明 - LM111 |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |