データシートサーチシステム
  Japanese  ▼
ALLDATASHEET.JP

X  

LS7560N データシート(PDF) 2 Page - LSI Computer Systems

部品番号 LS7560N
部品情報  BRUSHLESS DC MOTOR CONTROLLER
Download  8 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
メーカー  LSI [LSI Computer Systems]
ホームページ  http://www.lsicsi.com
Logo LSI - LSI Computer Systems

LS7560N データシート(HTML) 2 Page - LSI Computer Systems

  LS7560N Datasheet HTML 1Page - LSI Computer Systems LS7560N Datasheet HTML 2Page - LSI Computer Systems LS7560N Datasheet HTML 3Page - LSI Computer Systems LS7560N Datasheet HTML 4Page - LSI Computer Systems LS7560N Datasheet HTML 5Page - LSI Computer Systems LS7560N Datasheet HTML 6Page - LSI Computer Systems LS7560N Datasheet HTML 7Page - LSI Computer Systems LS7560N Datasheet HTML 8Page - LSI Computer Systems  
Zoom Inzoom in Zoom Outzoom out
 2 / 8 page
background image
ERROR AMPLIFIER Inputs (Pins 6, 7) Output (Pin 8)
For closed loop control, the Tachometer Output is applied through
a resistor to the negative input of the Error Amplifier on Pin 7. A
speed control potentiometer is connected to the positive input of
the Error Amplifier on Pin 6. A parallel RC Network is connected
between the Output of the Error Amplifier on Pin 8 and Pin 7. The
Amplifier, configured this way, enables the variable pulse width to
be converted to a DC voltage which is used to control the motor
speed. The potentiometer is used to set the desired motor speed.
For open loop control, configure the Error Amplifier as a voltage
follower by connecting Pin 7 directly to Pin 8 and do not connect
the Tachometer Output signal to the Error Amplifier.
TOP DRIVER POLARITY SELECT Input (Pin 20)
A High on this input selects a High Polarity to enable the Top Out-
put Motor Drivers and a Low selects a Low Polarity to enable the
Top Output Motor Drivers.
OUTPUT DRIVERS (Pins 12, 13, 14, 15, 16, 17)
Each Driver Output provides a CMOS compatible signal for driv-
ing Buffers/Power Transistors. The Outputs are capable of sink-
ing/sourcing 25mA with a 1.5V drop across the IC, at VDD = 12V.
FAULT INDICATOR Output (Pin 3)
Open drain output to provide sinking current for driving an ex-
ternal device, such as a LED, through an emitter follower (see
Figure 3) to indicate a malfunction condition. The output occurs
under any of the following conditions:
1) Overcurrent Sense condition
2) Enable Input below VR / 2.2
3) Invalid Sensor code
4) Chip power supply less than 9V
5) VR Output less than 4.1V
VR Output (Pin 19)
6V Reference Voltage Output that can supply 20mA of current at
VDD = 12V for powering input Sensors.
VDD (Pin 28) Supply Voltage positive terminal.
OSCILLATOR (Pin 9)
An external RC network is connected to this input to set the fre-
quency of the Sawtooth Schmitt Trigger Oscillator. The Sawtooth
is applied to the PWM Comparator along with the output of the Er-
ror Amplifier. The output of the PWM Comparator is a Pulse
Width Modulated Signal which is used to vary the effective drive
to the motor and, hence, the motor speed.
OVERCURRENT SENSE (Pins 10, 11)
The input to Pin 10 comes from the high side of a fractional ohm
current sensing resistor. The voltage at this input is compared to
an internal 100mV Reference. When the voltage exceeds the
100mV Reference, an Overcurrent Condition exists and the Out-
put Drivers are switched Off until the end of the sawtooth os-
cillator ramp-up. When the sawtooth switches low, the Over-
current Condition is sampled, and if it no longer exists, the Output
Drivers are switched On again. Otherwise, the Output Drivers re-
main Off until the end of the next sawtooth. The input to Pin 11
comes from the low side (Gnd) of the current sensing resistor and
connects to the low side of the internal 100mV Reference.
PWM CONTROL Input (Pin 21)
A High on this input causes only the Bottom Drivers to be Pulse
Width Modulated. A Low on this input causes both Top and Bot-
tom Drivers to have PWM.
TACHOMETER Output (Pin 5)
The output of the Frequency To Pulse Width Converter is tied to
this pin. The Converter uses the three Sensor Inputs and external
RC Network to generate a variable frequency output with a fixed
positive pulse width.
RC Input (Pin 4)
The external RC network connected to this input programs the
positive pulse width of the Frequency to Pulse Width Converter.
VSS (Pin 18) Supply Voltage negative terminal.
7560N-030906-2
MAXIMUM RATINGS (Voltages referenced to Vss)
SYMBOL
VALUE
UNIT
Power Supply Voltage
VDD
20
V
Voltage at any input
VIN
VsS - 0.5 to VR
V
Operating Temperature
TA
-25 to +85
°C
Storage Temperature
TSTG
-65 to +150
°C
Output Drive Sink/Source Current
Io
75
mA
VR Output Source Current
IR
30
mA
ELECTRICAL CHARACTERISTICS
VDD = 12V, RT = 47k
Ω, CT = 0.001µF, RS = 10kΩ, CS= 0.01µF, RF = 5.6kΩ (See Figure 3) TA = 25°C, unless otherwise specified
PARAMETER
SYMBOL
MIN
TYP
MAX
UNIT
Reference Voltage
VR
5.7
6.0
6.35
V
Line Regulation
∆VR
-
100
200
mV
VDD = 10V to 18V, IREF = 1.0mA
Temperature Stability
TA = 0°C to 70°C
∆VR
-
+/- 1.0
-
%
TA = 0°C to 85°C
∆VR
-
+/- 1.3
-
%
Error Amplifier:
Input Offset Voltage
VIO
-
5
15
mV
Input Current
IIN
-
0
10
nA
Input Common Mode Voltage Range
VICR
(0 to VR)
V
Open Loop Voltage Gain (RL = 15k
Ω)
AVOL
70
80
-
dB
Common Mode Rejection Ratio
CMRR
60
-
-
dB
Power Supply Rejection Ratio
PSRR
60
-
-
dB


同様の部品番号 - LS7560N

メーカー部品番号データシート部品情報
logo
LSI Computer Systems
LS7560N LSI-LS7560N_12 Datasheet
387Kb / 8P
   BRUSHLESS DC MOTOR CONTROLLER
More results

同様の説明 - LS7560N

メーカー部品番号データシート部品情報
logo
ON Semiconductor
MC33033 ONSEMI-MC33033_07 Datasheet
413Kb / 27P
   Brushless DC Motor Controller
January, 2007 ??Rev. 9
MC33033 ONSEMI-MC33033 Datasheet
530Kb / 24P
   BRUSHLESS DC MOTOR CONTROLLER
1996 REV 3
logo
LSI Computer Systems
LS7560 LSI-LS7560 Datasheet
97Kb / 8P
   BRUSHLESS DC MOTOR CONTROLLER
logo
Texas Instruments
UCC2626DW TI1-UCC2626DW Datasheet
685Kb / 23P
[Old version datasheet]   BRUSHLESS DC MOTOR CONTROLLER
logo
Sensitron
UC1625L SENSITRON-UC1625L Datasheet
62Kb / 4P
   BRUSHLESS DC MOTOR CONTROLLER
logo
Integral Corp.
IL33035 INTEGRAL-IL33035 Datasheet
124Kb / 3P
   BRUSHLESS DC MOTOR CONTROLLER
logo
Texas Instruments
UC1625 TI-UC1625 Datasheet
313Kb / 15P
[Old version datasheet]   Brushless DC Motor Controller
logo
ON Semiconductor
MC33035 ONSEMI-MC33035_06 Datasheet
527Kb / 28P
   Brushless DC Motor Controller
April, 2006 ??Rev. 8
logo
Texas Instruments
UCC2626 TI-UCC2626 Datasheet
209Kb / 15P
[Old version datasheet]   Brushless DC Motor Controller
DRV8307 TI1-DRV8307_16 Datasheet
1,007Kb / 33P
[Old version datasheet]   Brushless DC Motor Controller
logo
FOSLINK SEMICONDUCTOR C...
FSP33035 FOSLINK-FSP33035 Datasheet
1Mb / 28P
   BRUSHLESS DC MOTOR CONTROLLER
More results


Html Pages

1 2 3 4 5 6 7 8


データシート ダウンロード

Go To PDF Page


リンク URL




プライバシーポリシー
ALLDATASHEET.JP
ALLDATASHEETはお客様のビジネスに役立ちますか?  [ DONATE ] 

Alldatasheetは   |   広告   |   お問い合わせ   |   プライバシーポリシー   |   リンク交換   |   メーカーリスト
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com