 |
データシートサーチシステム |
|
|
データシートサーチシステム |
|
ST10F273E データシート(PDF) 28 Page - STMicroelectronics |
|
||||||||||||||||||||||||||||||
ST10F273E データシート(HTML) 28 Page - STMicroelectronics |
|
|
28 / 179 page  Internal Flash memory ST10F273E 28/179 5.2.3 Low power mode The Flash module is automatically switched off executing PWRDN instruction. The consumption is drastically reduced, but exiting this state can require a long time (tPD). Recovery time from Power down mode for the Flash modules is anyway shorter than the main oscillator start-up time. To avoid any problem in restarting to fetch code from the Flash, it is important to size properly the external circuit on RPD pin. Note: PWRDN instruction must not be executed while a Flash program/erase operation is in progress. 5.3 Write operation The Flash module have one single register interface mapped in the memory space 0x0E 0000 to 0x0E 0015. All the operations are enabled through four 16-bit control registers: Flash Control Register 1-0 High/Low (FCR1H/L-FCR0H/L). Eight other 16-bit registers are used to store Flash Address and Data for Program operations (FARH/L and FDR1H/L- FDR0H/L) and Write Operation Error flags (FERH/L). All registers are accessible with 8 and 16-bit instructions (since operates in 16-bit mode when in read/ write). Before accessing the Flash registers used for program/erasing operations, bit 5 (XFLASHEN) in XPERCON register shall be set. The two banks have their own dedicated sense amplifiers, so that one bank can be read while the other is written. During a Flash write operation, any attempt to read the bank under modification will output invalid data (software trap 009Bh). This means that the Flash bank is not fetchable when a programming operation is active: The write operation commands must be executed from another bank or from the other memory (internal RAM or external memory). During a Write operation, when bit LOCK of FCR0 is set, it is forbidden to write into the Flash Control Registers. Table 6. Control register interface Name Description Addresses Size Bus size FCR1-0 Flash control registers 1-0 0x000E 0000 - 0x000E 0007 8 byte 16-bit (XBUS) FDR1-0 Flash data registers 1-0 0x000E 0008 - 0x000E 000F 8 byte FAR Flash address registers 0x000E 0010 - 0x000E 0013 4 byte FER Flash error register 0x000E 0014 - 0x000E 0015 2 byte FNVWPIR Flash non volatile protection I register 0x000E DFB4 - 0x000E DFB7 4 byte FNVAPR0 Flash Non volatile access protection register 0 0x000E DFB8 - 0x000E DFB9 2 byte FNVAPR1 Flash non volatile access protection register 1 0x000E DFBC - 0x000E DFBF 4 byte |
同様の部品番号 - ST10F273E |
|
同様の説明 - ST10F273E |
|
|
リンク URL |
| プライバシーポリシー |
| ALLDATASHEET.JP |
| ALLDATASHEETはお客様のビジネスに役立ちますか？ [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Japanese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
