L6560D datasheet(4/11 Pages) STMICROELECTRONICS

部品番号	L6560D

部品情報	POWER FACTOR CORRECTOR

Download	11 Pages

Scroll/Zoom	100%

メーカー	STMICROELECTRONICS [STMicroelectronics]

ホームページ	http://www.st.com

Logo

4 / 11 page

OVER VOLTAGE PROTECTION OVP

The output voltage is expected to be kept by the

operation of the PFC circuits close to its reference

value that is set by the ratio of the two external re-

sistors R1 and R2 (see fig. 2), taking into consid-

eration that the non inverting input of the error

amplifier is biased inside the L6560 at 2.5V.

In steady state conditions, the current through R1

and R2 is:

ISC

=

∆Voutsc − 2.5

R1

or ISC =

2.5

R2

and, if the external compensation network is

made only with a capacitor C, the current through

C is equal zero.

When the output voltage increases abruptly the

current through R1 becomes:

IR1

=

Vout

− 2.5

R1

IR1 =

Voutsc

+∆VOUT − 2.5

R1

= Isc +∆I.

Since the current through R2 doesn’t change, the

∆I current must flow through the capacitor C and

enter in the error amplifier.

This current is mirrored inside the L6560, and

compared with a precise internal reference of

40

µA. Whenever such 40µA limit is exceed, the

OVP protection is triggered (Dynamic OVP), and

the external power transistor is switched off, until

the overvoltage situation disappears. However if

the overvoltage persists, before that the transient

condition of dynamic circuit exhausts, an internal

comparator (Static OVP) latches the OVP condi-

tion keeping the external power switch turned off

(see fig. 1).

The OVP value is threfore set by the equation

OVP =

∆Vout = R1 ⋅ 40µA.

Typical values for R1,R2 and C are reported in

the application circuit. The overvoltage can be set

independently from the average output voltage.

The precision in setting the overvoltage threshold

is 7% of the overvoltage value (for instance

∆V=

60V

± 4.2V).

ELECTRICAL CHARACTERISTICS (continued)

ZERO CURRENT DETECTOR

Symbol

Parameter

Test Condition

Min.

Typ.

Max.

Unit

VZCD

5

Input Threshold Voltage Rising

Edge

1.8

2.3

V

Hysteresis

0.3

0.5

0.7

V

VZCD

5

Clamp Voltage

IZCD = 3mA

5

5.7

6.4

V

VZCD

5

Clamp Voltage

IZCD = –3mA

0.4

0.7

1

V

OUTPUT SECTION

Symbol

Parameter

Test Condition

Min.

Typ.

Max.

Unit

VGD

7

Dropout Voltage

IGDsource = 200mA

1.2

2

V

IGDsource = 20mA

0.7

1

V

IGDsink = 200mA

1.5

V

IGDsink = 20mA

0.3

V

tr

7

Output Voltage Rise Time

CL = 1nF

50

120

ns

tf

7

Output Voltage Fall Time

CL = 1nF

40

100

ns

OUTPUT OVERVOLTAGE SECTION

Symbol

Parameter

Test Condition

Min.

Typ.

Max.

Unit

IOVP

2

OVP Triggering Current

36

40

44

µA

RESTART TIMER

Symbol

Parameter

Test Condition

Min.

Typ.

Max.

Unit

tSTART

Start Timer

45

60

µs

L6560 - L6560A

4/11

同様の部品番号 - L6560D

メーカー	部品番号	データシート	部品情報
STMicroelectronics	L6561	180Kb / 11P	POWER FACTOR CORRECTOR April 1999
	L6561	180Kb / 13P	POWER FACTOR CORRECTOR
	L6561D	180Kb / 11P	POWER FACTOR CORRECTOR April 1999
	L6561D013TR	180Kb / 11P	POWER FACTOR CORRECTOR April 1999
Intersil Corporation	L6562	45Kb / 5P	Microprocessor CORE Voltage Regulator Two-Phase Buck PWM Controller

More results

同様の説明 - L6560D

メーカー	部品番号	データシート	部品情報
Unisonic Technologies	L8562	266Kb / 6P	POWER FACTOR CORRECTOR
STMicroelectronics	L4981AD013TR	2Mb / 16P	POWER FACTOR CORRECTOR
Unisonic Technologies	L8561	224Kb / 5P	POWER FACTOR CORRECTOR
Unisonic Technologies	UA7524	204Kb / 5P	POWER FACTOR CORRECTOR
AUK corp	S6500	492Kb / 7P	POWER FACTOR CORRECTOR
STMicroelectronics	L4981A	228Kb / 17P	POWER FACTOR CORRECTOR September 1998
	EVAL6561-80	180Kb / 13P	POWER FACTOR CORRECTOR
	E-L6561D013TR	180Kb / 13P	POWER FACTOR CORRECTOR
	L4981A	2Mb / 16P	POWER FACTOR CORRECTOR
Unisonic Technologies	8561	162Kb / 6P	POWER FACTOR CORRECTOR