データシートサーチシステム |
|
TDA7338D013TR データシート(PDF) 6 Page - STMicroelectronics |
|
TDA7338D013TR データシート(HTML) 6 Page - STMicroelectronics |
6 / 12 page TDA7338 6/12 Figure 5. High Cut Control Figure 6. Stereo Blend -0.5 -0.4 -0.3 -0.2 -0.1 0.0 VHCC-VR(V) 0 1 2 3.18 (=50 µs) fc (KHz) VR=3.6V D95AU366 -0.40 -0.32 -0.24 -0.16 -0.08 VSB-VR(V) 0 10 20 30 40 50 SEP (dB) VR=3.6V D95AU367 Furthermore the conditions of the stereo separation (see fig.6) can be controlled through the signal applied to Pin 16 (VSB). Both signal levels (VSB and VHCC) are referred to Pin 17 (VR), with the characteristic that the control range is 11% of VR. By modifying the feedback resistor value of the output stages (Pin 9 - 10, Pin 11 - 12) the total gain of the stereodecoder can be modified. Pin 7 and Pin 8 have an additional function. By pulling them to ground the VCO-OFF (Pin 7) and the MUTE (Pin 8) function are activated. The MUTE signal disconnects the MPX-signal from the circuit, while in com- bination with VCO-OFF also the output buffers are disconnected from the circuit. In this mode the output buffers can be used for AM-stereo, cassette play back and other purposes. 4.2 AM Mono Mode By selecting VCO-OFF (Pin 7 to GND) the VCO is switched off and the SB and HCC are disabled. The deemphasis time constant is changed to 40 µs (fc = 4KHz). 4.3 DESCRIPTION OF THE NOISE BLANKER In the normal automotive environment the MPX signal is disturbed by ignition spikes, motors and high fre- quency switches etc. The aim of the noise blanker part is to cancel the influence of the spikes produced by these components. Therefore the output of the stereodecoder is switched off for a time of 40 µs (average spike duration). In a first stage the spikes must be detected but to avoid a wrong triggering on high frequency noise a com- plex trigger control is implemented. Behind the trigger stage a pulse former generates the 40ms "blanking" pulse. This duration of 40 µs can be varied by changing the capacitor at pin 7. 4.3.1 Trigger Path The incoming MPX signal is highpass-filtered, amplified and rectified (block RECT-PEAK). The second order highpass-filter has a corner-frequency of 140KHz. The rectifier signal, RECT, is used to generate by peak-rectification a signal called PEAK, which is avail- able at the PEAK pin 8. Also noise with a frequency >100KHz increases the PEAK voltage. The value of the PEAK voltage influ- ences the trigger threshold voltage Vth (block ATC). The higher the noise level the higher the threshold. Both signals, RECT and PEAK+Vth are fed to a comparator (block PEAK-COMP) which outputs a saw- tooth-shaped waveform at the TBLANK pin 7. A second comparator (block BLANK-COMP) forms the in- ternal blanking duration of 40 µs. The noise blanker is supplied by his own biasing circuit (block BIAS- MONO) to avoid any cross talk to the signal path (block BIAS-MONO). |
同様の部品番号 - TDA7338D013TR |
|
同様の説明 - TDA7338D013TR |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |