データシートサーチシステム |
|
TDA7405 データシート(PDF) 11 Page - STMicroelectronics |
|
TDA7405 データシート(HTML) 11 Page - STMicroelectronics |
11 / 56 page 11/56 TDA7405 2.1.3 Mono-differential Input 1 (MD1) The MD1-input is designed as a basic differential stage with 56k Ω input-impedance. This input is configurable as a single-ended stereo input (see pin-out). 2.1.4 Mono-differential Input 2 (MD2) The MD2-input has the same topology as MD1, but without the possibility to configure it to single ended. 2.1.5 Single-ended stereo Input (SE1), single-ended mono input (AM) and FM-MPX input All single ended inputs offer an input impedance of 100kW. The AM-pin can be connected by software to the input of the stereodecoder in order to use the AM-Noiseblanker and AM-High-Cut feature. 2.2 AutoZero The AutoZero allows a reduction of the number of pins as well as external components by canceling any offset generated by or before the In-Gain-stage (Please notice that externally generated offsets, e.g. generated through the leakage current of the coupling capacitors, are not canceled). The auto-zeroing is started every time the DATA-BYTE 0 is selected and needs max. 0.3ms for the alignment. To avoid audible clicks the Audioprocessor is muted before the loudness stage during this time. The AutoZero- feature is only present in the main signal-path. 2.2.1 AutoZero for Stereodecoder-Selection A special procedure is recommended for selecting the stereodecoder at the main input-selector to guarantee an optimum offset-cancellation: (Step 0: SoftMute or Mute the signal-path) Step 1: Temporary deselect the stereodecoder at all input-selectors Step 2: Configure the stereodecoder via IIC-Bus Step 3: Wait 1ms Step 4: Select the stereodecoder at the main input-selector first The root cause of this procedure is, that after muting the stereodecoder (Step 1), the internal stereodecoder filters have to settle in order to perform a proper offset-cancellation. 2.2.2 AutoZero-Remain In some cases, for example if the µP is executing a refresh cycle of the IIC-Bus-programming, it is not useful to start a new AutoZero-action because no new source is selected and an undesired mute would appear at the outputs. For such applications the A631 could be switched in the AutoZero-Remain-Mode (Bit 6 of the subad- dress-byte). If this bit is set to high, the DATABYTE 0 could be loaded without invoking the AutoZero and the old adjustment-value remains. 2.3 Pause Detector / MUX-Output The pin number 40(Pause/MUX) is configurable for two different functions: 1. During Pause-Detector OFF this pin is used as a mono-output of the main input-selector. This signal is often used to drive a level-/equalizer-display on the carradio front-panel. 2. During Pause-Detector ON the pin is used to define the time-constant of the detector by an external ca- pacitor. The pause-detector is driven by the internal stereodecoder-outputs in order to use pauses in the FM-signal for alternate-frequency-jumps. If the signal-level of both stereodecoder channels is outside the programmed volt- age-window, the external capacitor is abruptly discharged. Inside the pause-condition the capacitor is slowly re- charged by a constant current of 25µA. The pause information is also available via IIC-Bus (see IIC-Bus programming). |
同様の部品番号 - TDA7405 |
|
同様の説明 - TDA7405 |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |