データシートサーチシステム |
|
TLC1543IDW データシート(PDF) 6 Page - Texas Instruments |
|
|
TLC1543IDW データシート(HTML) 6 Page - Texas Instruments |
6 / 27 page TLC1542C, TLC1542I, TLC1542M, TLC1542Q, TLC1543C, TLC1543I, TLC1543Q 10-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 11 ANALOG INPUTS SLAS052E – MARCH 1992 – OCTOBER 1998 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 analog inputs and test modes (continued) Table 2. Analog-Channel-Select Address ANALOG INPUT SELECTED VALUE SHIFTED INTO ADDRESS INPUT SELECTED BINARY HEX A0 0000 0 A1 0001 1 A2 0010 2 A3 0011 3 A4 0100 4 A5 0101 5 A6 0110 6 A7 0111 7 A8 1000 8 A9 1001 9 A10 1010 A Table 3. Test-Mode-Select Address INTERNAL SELF-TEST VOLTAGE VALUE SHIFTED INTO ADDRESS INPUT OUTPUT RESULT (HEX)‡ VOLTAGE SELECTED† BINARY HEX OUTPUT RESULT (HEX)‡ Vref+ – Vref– 2 1011 B 200 Vref– 1100 C 000 Vref+ 1101 D 3FF † Vref+ is the voltage applied to the REF+ input, and Vref–is the voltage applied to the REF– input. ‡ The output results shown are the ideal values and vary with the reference stability and with internal offsets. converter and analog input The CMOS threshold detector in the successive-approximation conversion system determines each bit by examining the charge on a series of binary-weighted capacitors (see Figure 1). In the first phase of the conversion process, the analog input is sampled by closing the SC switch and all ST switches simultaneously. This action charges all the capacitors to the input voltage. In the next phase of the conversion process, all ST and SC switches are opened and the threshold detector begins identifying bits by identifying the charge (voltage) on each capacitor relative to the reference (REF –) voltage. In the switching sequence, ten capacitors are examined separately until all ten bits are identified and then the charge-convert sequence is repeated. In the first step of the conversion phase, the threshold detector looks at the first capacitor (weight = 512). Node 512 of this capacitor is switched to the REF+ voltage, and the equivalent nodes of all the other capacitors on the ladder are switched to REF –. If the voltage at the summing node is greater than the trip point of the threshold detector (approximately one-half VCC), a 0 bit is placed in the output register and the 512-weight capacitor is switched to REF –. If the voltage at the summing node is less than the trip point of the threshold detector, a 1 bit is placed in the register and the 512-weight capacitor remains connected to REF + through the remainder of the successive-approximation process. The process is repeated for the 256-weight capacitor, the 128-weight capacitor, and so forth down the line until all bits are counted. |
同様の部品番号 - TLC1543IDW |
|
同様の説明 - TLC1543IDW |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |