データシートサーチシステム |
|
FAN9611_1112 データシート(PDF) 1 Page - Fairchild Semiconductor |
|
FAN9611_1112 データシート(HTML) 1 Page - Fairchild Semiconductor |
1 / 36 page December 2011 © 2008 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN9611 / FAN9612 • Rev. 1.1.4 FAN9611 / FAN9612 Interleaved Dual BCM PFC Controllers Features Sync-Lock™ Interleaving Technology for 180° Out-of-Phase Synchronization Under All Conditions Automatic Phase Disable at Light Load Dead-Phase Detect Protection 2.0A Sink, 1.0A Source, High-Current Gate Drivers High Power Factor, Low Total Harmonic Distortion Voltage-Mode Control with (VIN)2 Feedforward Closed-Loop Soft-Start with User-Programmable Soft-Start Time for Reduced Overshoot Minimum Restart Frequency to Avoid Audible Noise Maximum Switching Frequency Clamp Brownout Protection with Soft Recovery Non-Latching OVP on FB Pin and Latching Second- Level Protection on OVP Pin Open-Feedback Protection Power-Limit and Current Protection for Each Phase Low Startup Current of 80µA Typical Works with DC and 50Hz to 400Hz AC Inputs Applications 100-1000W AC-DC Power Supplies Large Screen LCD-TV, PDP-TV, RP-TV Power High-Efficiency Desktop and Server Power Supplies Networking and Telecom Power Supplies Solar Micro Inverters Description The FAN9611/12 family of interleaved dual Boundary- Conduction-Mode (BCM) Power-Factor-Correction (PFC) controllers operate two parallel-connected boost power trains 180° out of phase. Interleaving extends the maximum practical power level of the control technique from about 300W to greater than 800W. Unlike the continuous conduction mode (CCM) technique often used at higher power levels, BCM offers inherent zero- current switching of the boost diodes, which permits the use of less expensive diodes without sacrificing efficiency. Furthermore, the input and output filters can be smaller due to ripple current cancellation and effective doubling of the switching frequency. The converters operate with variable frequency, which is a function of the load and the instantaneous input / output voltages. The switching frequency is limited between 16.5kHz and 525kHz. The Pulse Width Modulators (PWM) implement voltage-mode control with input voltage feedforward. When configured for PFC applications, the slow voltage regulation loop results in constant on-time operation within a line cycle. This PWM method, combined with the BCM operation of the boost converters, provides automatic power factor correction. The controllers offers bias UVLO (10V / 7.5V for FAN9611 and 12.5V / 7.5V for FAN9612), input brownout, over-current, open-feedback, output over- voltage, and redundant latching over-voltage protections. Furthermore, the converters’ output power is limited independently of the input RMS voltage. Synchronization between the power stages is maintained under all operating conditions. Figure 1. Simplified Application Diagram |
同様の部品番号 - FAN9611_1112 |
|
同様の説明 - FAN9611_1112 |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |