データシートサーチシステム
  Japanese  ▼
ALLDATASHEET.JP

X  

AD420AR-32 データシート(PDF) 8 Page - Analog Devices

部品番号 AD420AR-32
部品情報  Serial Input 16-Bit 4 mA-20 mA, 0 mA-20 mA DAC
Download  11 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
メーカー  AD [Analog Devices]
ホームページ  http://www.analog.com
Logo AD - Analog Devices

AD420AR-32 データシート(HTML) 8 Page - Analog Devices

Back Button AD420AR-32 Datasheet HTML 3Page - Analog Devices AD420AR-32 Datasheet HTML 4Page - Analog Devices AD420AR-32 Datasheet HTML 5Page - Analog Devices AD420AR-32 Datasheet HTML 6Page - Analog Devices AD420AR-32 Datasheet HTML 7Page - Analog Devices AD420AR-32 Datasheet HTML 8Page - Analog Devices AD420AR-32 Datasheet HTML 9Page - Analog Devices AD420AR-32 Datasheet HTML 10Page - Analog Devices AD420AR-32 Datasheet HTML 11Page - Analog Devices  
Zoom Inzoom in Zoom Outzoom out
 8 / 11 page
background image
REV. F
–8–
AD420
THREE-WIRE INTERFACE
Figure 8 shows the AD420 connected in the three-wire interface
mode. The AD420 data input block contains a serial input shift
register and a parallel latch. The contents of the shift register are
controlled by the DATA IN signal and the rising edges of the
CLOCK. Upon request of the LATCH pin the DAC and inter-
nal latch are updated from the shift register parallel outputs.
The CLOCK should remain inactive while the DAC is updated.
Refer to the timing requirements for three-wire interface.
RLOAD
FAULT
DETECT
VCC
LATCH
CLOCK
DATA
IN
GND
DATA
OUT
IOUT
AD420
DAC1
VCC
LATCH
VLL
VCC
FAULT
DETECT
CLOCK
DATA
IN
GND
DATA
OUT
AD420
DAC2
IOUT
10k
FAULT DETECT
VCC
RLOAD
LATCH
CLOCK
DATA IN
Figure 8. Three-Wire Interface Using Multiple DACs with
Joint Fault Detect
USING MULTIPLE DACS WITH FAULT DETECT
The three-wire interface mode can utilize the serial DATA
OUT for easy interface to multiple DACs. To program the two
AD420s in Figure 8, 32 data bits are required. The first 16 bits
are clocked into the input shift register of DAC1. The next 16
bits transmitted pass the first 16 bits from the DATA OUT pin
of DAC1 to the input register of DAC2. The input shift regis-
ters of the two DACs operate as a single 32-bit shift register,
with the leading 16 bits representing information for DAC2 and
the trailing 16 bits serving for DAC1. Each DAC is then up-
dated upon request of the LATCH pin. The daisy-chain can be
extended to as many DACs as required.
ASYNCHRONOUS INTERFACE USING OPTOCOUPLERS
The AD420 connected in ASYNCHRONOUS INTERFACE
mode with optocouplers is shown in Figure 9. Asynchronous
operation minimizes the number of control signals required for
isolation of the digital system from the control loop. The resistor
connected between the LATCH pin and VCC is required to
activate this mode. For operation with VCC below 18 V use a
50 k
Ω pull-up resistor, from 18 V–32 V use 100 kΩ. Asynchro-
nous mode requires that the clock run at 16 times the data bit
rate, therefore to operate at the maximum input data rate of
150 kBPS an input clock of 2.4 MHz is required. The actual
data rate achieved may be limited by the type of optocouplers
chosen. The number of control signals can further be reduced
by creating the appropriate clock signal on the current loop side
of the isolation barrier. If optocouplers with relatively slow rise
and fall times are used, Schmitt triggers may be required on the
digital inputs to prevent erroneous data being presented to the
DAC.
VCC
GND
LATCH
CLOCK
DATA IN
VLL
CLOCK
+5V
DATA
ISOLATION
GALVANIC
BARRIER
+24V
11
2
8
23
7
9
100k
AD420
Figure 9. Asynchronous Interface Using Optocouplers


同様の部品番号 - AD420AR-32

メーカー部品番号データシート部品情報
logo
Analog Devices
AD420AR-32 AD-AD420AR-32 Datasheet
303Kb / 16P
   Serial Input 16-Bit 4 mA??0 mA, 0 mA??0 mA DAC
Rev. H
AD420AR-32 AD-AD420AR-32 Datasheet
303Kb / 16P
   Serial Input 16-Bit 4 mA??0 mA, 0 mA??0 mA DAC
Rev. H
AD420AR-32-REEL AD-AD420AR-32-REEL Datasheet
303Kb / 16P
   Serial Input 16-Bit 4 mA??0 mA, 0 mA??0 mA DAC
Rev. H
AD420AR-32-REEL AD-AD420AR-32-REEL Datasheet
303Kb / 16P
   Serial Input 16-Bit 4 mA??0 mA, 0 mA??0 mA DAC
Rev. H
More results

同様の説明 - AD420AR-32

メーカー部品番号データシート部品情報
logo
Analog Devices
AD420 AD-AD420_11 Datasheet
303Kb / 16P
   Serial Input 16-Bit 4 mA??0 mA, 0 mA??0 mA DAC
Rev. H
AD420ANZ-32 AD-AD420ANZ-32 Datasheet
303Kb / 16P
   Serial Input 16-Bit 4 mA??0 mA, 0 mA??0 mA DAC
Rev. H
AD420 AD-AD420_15 Datasheet
303Kb / 16P
   Serial Input 16-Bit 4 mA??0 mA, 0 mA??0 mA DAC
Rev. H
AD5421 AD-AD5421_11 Datasheet
757Kb / 32P
   16-Bit, Serial Input, Loop-Powered, 4 mA to 20 mA DAC
REV. 0
AD5421 AD-AD5421_13 Datasheet
726Kb / 36P
   16-Bit, Serial Input, Loop-Powered, 4 mA to 20 mA DAC
Rev. F
UG-250 AD-UG-250 Datasheet
562Kb / 12P
   Evaluation Board for 16-Bit, Serial Input, Loop-Powered 4 mA to 20 mA DAC
REV. A
AD5735 AD-AD5735_12 Datasheet
1Mb / 48P
   Quad-Channel, 12-Bit, Serial Input, 4 mA to 20 mA
REV. B
AD5757 AD-AD5757_11 Datasheet
1Mb / 44P
   Quad Channel, 16-Bit,Serial Input, 4 mA to 20 mA Output DAC, Dynamic Power Control
REV. A
AD421BNZ AD-AD421BNZ Datasheet
173Kb / 14P
   Loop-Powered 4 mA to 20 mA DAC
REV. C
AD421 AD-AD421_15 Datasheet
173Kb / 14P
   Loop-Powered 4 mA to 20 mA DAC
REV. C
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11


データシート ダウンロード

Go To PDF Page


リンク URL




プライバシーポリシー
ALLDATASHEET.JP
ALLDATASHEETはお客様のビジネスに役立ちますか?  [ DONATE ] 

Alldatasheetは   |   広告   |   お問い合わせ   |   プライバシーポリシー   |   リンク交換   |   メーカーリスト
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com