データシートサーチシステム |
|
AD8079 データシート(PDF) 9 Page - Analog Devices |
|
AD8079 データシート(HTML) 9 Page - Analog Devices |
9 / 12 page 9 REV. A AD8079 –9– The current feedback nature of the op amps, in addition to enabling the wide bandwidth, provides an output drive of more than 3 V p-p into a 20 Ω load for each output at 20 MHz. On the other hand, the voltage feedback nature provides symmetri- cal high impedance inputs and allows the use of reactive compo- nents in the feedback network. The circuit consists of the two op amps each configured as a unity gain follower by the 750 Ω feedback resistors between each op amp’s output and inverting input. The output of each op amp has a 750 Ω resistor to the inverting input of the other op amp. Thus, each output drives the other op amp through a unity gain inverter configuration. By connecting the two ampli- fiers as cross-coupled inverters, their outputs are free to be equal and opposite, assuring zero-output common-mode voltage. With this circuit configuration, the common-mode signal of the outputs is reduced. If one output moves slightly higher, the negative input to the other op amp drives its output to go slightly lower and thus preserves the symmetry of the comple- mentary outputs which reduces the common-mode signal. The resulting architecture offers several advantages. First, the gain can be changed by changing a single resistor. Changing either RF or RG will change the gain as in an inverting op amp circuit. For most types of differential circuits, more than one resistor must be changed to change gain and still maintain good CMR. Reactive elements can be used in the feedback network. This is in contrast to current feedback amplifiers that restrict the use of reactive elements in the feedback. The circuit described requires about 1.3 pF of capacitance in shunt across RF in order to opti- mize peaking and realize a –3 dB bandwidth of more than 110 MHz. The peaking exhibited by the circuit is very sensitive to the value of this capacitor. Parasitics in the board layout on the or- der of tenths of picofarads will influence the frequency response and the value required for the feedback capacitor, so a good lay- out is essential. The shunt capacitor type selection is also critical. Good micro- wave type chip capacitors with high Q were found to yield best performance. FREQUENCY – Hz 0.1M 1G 1M 10M 100M CC = 1.3pF VIN = 10dBm 6 4 2 0 –2 –4 –6 –8 –10 –12 –14 OUT+ OUT– Figure 28. Differential Driver Frequency Response Layout Considerations The specified high speed performance of the AD8079 requires careful attention to board layout and component selection. Proper RF design techniques and low parasitic component se- lection are mandatory. The PCB should have a ground plane covering all unused por- tions of the component side of the board to provide a low im- pedance ground path. The ground plane should be removed from the area near the input pins to reduce stray capacitance. Chip capacitors should be used for supply bypassing (see Figure 29). One end should be connected to the ground plane and the other within 1/8 in. of each power pin. An additional large (4.7 µF–10 µF) tantalum electrolytic capacitor should be con- nected in parallel, but not necessarily so close, to supply current for fast, large-signal changes at the output. Stripline design techniques should be used for long signal traces (greater than about 1 in.). These should be designed with a characteristic impedance of 50 Ω or 75 Ω and be properly termi- nated at each end. |
同様の部品番号 - AD8079 |
|
同様の説明 - AD8079 |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |