データシートサーチシステム |
|
AD9060SZ データシート(PDF) 3 Page - Analog Devices |
|
AD9060SZ データシート(HTML) 3 Page - Analog Devices |
3 / 12 page AD9060 –3– REV. A Test AD9060JE/JZ AD9060KE/KZ Parameter (Conditions) Temp Level Min Typ Max Min Typ Max Units DYNAMIC PERFORMANCE (CONTINUED) Signal-to-Noise Ratio 6 (Without Harmonics) fIN = 2.3 MHz +25 °C I 54 56 54 58 dB fIN = 10.3 MHz +25 °C I 51 55 51 55 dB fIN = 29.3 MHz +25 °C I 46 48 46 48 dB Harmonic Distortion fIN = 2.3 MHz +25 °C I 61 65 61 65 dBc fIN = 10.3 MHz +25 °C I 55 58 55 58 dBc fIN = 29.3 MHz +25 °C I 47 50 47 50 dBc Two-Tone Intermodulation Distortion Rejection 7 +25 °C V 70 70 dBc Differential Phase +25 °C V 0.5 0.5 Degree Differential Gain +25 °CV 1 1 % ENCODE INPUT Logic “1” Voltage Full VI –1.1 –1.1 V Logic “0” Voltage Full VI –1.5 –1.5 V Logic “1” Current Full VI 150 300 150 300 µA Logic “0” Current Full VI 150 300 150 300 µA Input Capacitance +25 °CV 5 5 pF Pulse Width (High) +25 °CI 6 6 ns Pulse Width (Low) +25 °CI 6 6 ns DIGITAL OUTPUTS Logic “1” Voltage Full VI –1.1 –1.1 V Logic “0” Voltage Full VI –1.5 –1.5 V POWER SUPPLY +VS Supply Current +25 °C VI 420 500 420 500 mA Full VI 500 500 mA –VS Supply Current +25 °C VI 150 180 150 180 mA Full VI 190 190 mA Power Dissipation +25 °C VI 2.8 3.3 2.8 3.3 W Full VI 3.5 3.5 W Power Supply Rejection Ratio (PSRR) 8 Full VI 6 10 6 10 mV/V NOTES 1Absolute maximum ratings are limiting values to be applied individually and beyond which the serviceability of the circuit may be impaired. Functional operability is not necessarily implied. Exposure to absolute maximum rating conditions for an extended period of time may affect device reliability. 2Typical thermal impedances (part soldered onto board): 68-pin leaded ceramic chip carrier: θ JC = 1°C/W; θJA = 17°C/W (no air flow); θJA = 15°C/W (air flow = 500 LFM). 68-pin ceramic LCC: θ JC = 2.6°C/W; θJA = 15°C/W (no air flow); θJA = 13°C/W (air flow = 500 LFM). 33/4 REF, 1/2REF and 1/4REF reference ladder taps are driven from dc sources at +0.875 V, 0 V and –0.875 V, respectively. Outputs terminated through 100 Ω to –2.0 V; CL < 4 pF. Accuracy of the overflow comparator is not tested and not included in linearity specifications. 4Measured with ANALOG IN = +V SENSE 5Output delay measured as worst-case time from 50% point of the rising edge of ENCODE to 50% point of the slowest rising or falling edge of D 0–D9. Output skew measured as worst-case difference in output delay among D 0–D9. 6RMS signal to rms noise with analog input signal 1 dB below full scale at specified frequency. 7Intermodulation measured with analog input frequencies of 2.3 MHz and 3.0 MHz at 7 dB below full scale. 8Measured as the ratio of the worst-case change in transition voltage of a single comparator for a 5% change m +V S or –VS. Specifications subject to change without notice. |
同様の部品番号 - AD9060SZ |
|
同様の説明 - AD9060SZ |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |