データシートサーチシステム |
|
ADR423BR データシート(PDF) 5 Page - Analog Devices |
|
ADR423BR データシート(HTML) 5 Page - Analog Devices |
5 / 16 page REV. B ADR420/ADR421/ADR423/ADR425 –5– PARAMETER DEFINITIONS Temperature Coefficient The change of output voltage over the operating temperature range and normalized by the output voltage at 25 °C, expressed in ppm/ °C. The equation follows: TCV ppm C VT VT VC T T O OO O / () – () () ( – ) ° () = °× × 21 21 6 25 10 where VO (25 °C) = V O at 25 °C VO (T1) = VO at Temperature 1 VO (T2) = VO at Temperature 2. Line Regulation The change in output voltage due to a specified change in input voltage. It includes the effects of self-heating. Line regulation is expressed in either percent per volt, parts-per-million per volt, or microvolts per volt change in input voltage Load Regulation The change in output voltage due to a specified change in load current. It includes the effects of self-heating. Load regulation is expressed in either microvolts per milliampere, parts-per-million per milliampere, or ohms of dc output resistance. Long-Term Stability Typical shift of output voltage at 25 °C on a sample of parts subjected to operation life test of 1000 hours at 125 °C: ∆ ∆ VV t V t V ppm Vt Vt Vt OO O O OO O = =× () – ( ) () () – ( ) () 01 01 0 6 10 where VO (t0) = VO at 25 °C at Time 0 VO (t1) = VO at 25 °C after 1,000 hours operation at 125°C. Thermal Hysteresis Thermal hysteresis is defined as the change of output voltage after the device is cycled through temperature from +25 °C to –40 °C to +125°C and back to +25°C. This is a typical value from a sample of parts put through such a cycle. VV C V V ppm VC V VC O HYS O O TC O HYS OO TC O __ _ _ () – () () – () =° = ° ° × 25 25 25 10 6 where VO (25 °C) = V O at 25 °C VO_TC = VO at 25 °C after temperature cycle at +25°C to –40°C to +125 °C and back to +25°C. Input Capacitor Input capacitors are not required on the ADR42x. There is no limit for the value of the capacitor used on the input, but a 1 µF to 10 µF capacitor on the input will improve transient response in applications where the supply suddenly changes. An additional 0.1 µF in parallel will also help to reduce noise from the supply. Output Capacitor The ADR42x does not need output capacitors for stability under any load condition. An output capacitor, typically 0.1 µF, will filter out any low-level noise voltage and will not affect the operation of the part. On the other hand, the load transient response can be improved with an additional 1 µF to 10 µF output capacitor in parallel. A capacitor here will act as a source of stored energy for sudden increase in load current. The only parameter that will degrade, by adding an output capacitor, is turn-on time and it depends on the size of the capacitor chosen. |
同様の部品番号 - ADR423BR |
|
同様の説明 - ADR423BR |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |