データシートサーチシステム |
|
ADV7176AKS データシート(PDF) 3 Page - Analog Devices |
|
ADV7176AKS データシート(HTML) 3 Page - Analog Devices |
3 / 52 page –3– REV. B ADV7175A/ADV7176A Parameter Conditions 1 Min Typ Max Units STATIC PERFORMANCE3 Resolution (Each DAC) 10 Bits Accuracy (Each DAC) Integral Nonlinearity ±1 LSB Differential Nonlinearity Guaranteed Monotonic ±1 LSB DIGITAL INPUTS Input High Voltage, VINH 2V Input Low Voltage, VINL 0.8 V Input Current, IIN 3, 4 VIN = 0.4 V or 2.4 V ±1 µA Input Current, IIN 3, 5 VIN = 0.4 V or 2.4 V ±50 µA Input Capacitance, CIN 10 pF DIGITAL OUTPUTS Output High Voltage, VOH ISOURCE = 400 µA 2.4 V Output Low Voltage, VOL ISINK = 3.2 mA 0.4 V Three-State Leakage Current 3 10 µA Three-State Output Capacitance 3 10 pF ANALOG OUTPUTS 3 Output Current6, 7 16.5 17.35 18.5 mA Output Current 8 5mA DAC-to-DAC Matching 2.0 % Output Compliance, VOC 0 +1.4 V Output Impedance, ROUT 15 k Ω Output Capacitance, COUT IOUT = 0 mA 30 pF POWER REQUIREMENTS 3, 9 VAA 3.0 3.3 3.6 V Normal Power Mode IDAC (max) 10 150 155 mA IDAC (min) 10 20 mA ICCT 9 45 mA Low Power Mode IDAC (max) 10 75 mA IDAC (min) 10 15 mA ICCT 11 45 mA Power Supply Rejection Ratio COMP = 0.1 µF 0.01 0.5 %/% NOTES 11The max/min specifications are guaranteed over this range. The max/min values are typical over 3.0 V to 3.6 V. 12Temperature range T MIN to TMAX: 0 °C to 70°C. 13 Guaranteed by characterization. 14All digital input pins except pins RESET and RTC/SCRESET. 15Excluding all digital input pins except pins RESET and RTC/SCRESET. 16Full drive into 37.5 Ω load. 17DACs can output 35 mA typically at 3.3 V (R SET = 150 Ω and R L = 75 Ω), optimum performance obtained at 18 mA DAC current (R SET = 300 Ω and R L = 150 Ω. 18Minimum drive current (used with buffered/scaled output load). 19Power measurements are taken with Clock Frequency = 27 MHz. Max T J = 110 °C. 10I DAC is the total current (min corresponds to 5 mA output per DAC, max corresponds to 38 mA output per DAC) to drive all four DACs. Turning off individual DACs reduces IDAC correspondingly. 11I CCT (Circuit Current) is the continuous current required to drive the device. Specifications subject to change without notice. 3.3 V SPECIFICATIONS (V AA = +3.0 V – 3.6 V 1, VREF = 1.235 V RSET = 300 . All specifications TMIN to TMAX 2 unless otherwise noted) |
同様の部品番号 - ADV7176AKS |
|
同様の説明 - ADV7176AKS |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |