4

www.fairchildsemi.com

FM93C46A Rev. C.1

Ambient Storage Temperature

-65

°C to +150°C

All Input or Output Voltages

+6.5V to -0.3V

with Respect to Ground

Lead Temperature

(Soldering, 10 sec.)

+300

°C

ESD rating

2000V

Operating Conditions

Ambient Operating Temperature

FM93C46AL/LZ

0

°C to +70°C

FM93C46ALE/LZE

-40

°C to +85°C

FM93C46ALV/LZV

-40

°C to +125°C

Power Supply (V

2.7V to 5.5V

page 3 for V

Symbol

Parameter

Conditions

Min

Max

Units

I

CCA

Operating Current

CS = V

1

mA

Standby Current

L

10

µA

LZ (2.7V to 4.5V)

1

µA

I

IL

Input Leakage

V

±1

µA

I

OL

Output Leakage

(Note 2)

I

ILO

Input Leakage ORG Pin

ORG tied to V

CC

-1

1

µA

ORG tied to V

-2.5

2.5

Input Low Voltage

-0.1

V

V

IH

Input High Voltage

0.8V

CC

V

Output Low Voltage

V

V

OH

Output High Voltage

I

0.9V

CC

SK Clock Frequency

(Note 4)

0

250

KHz

t

SKH

SK High Time

1

µs

SK Low Time

1

µs

t

CS

Minimum CS Low Time

(Note 5)

1

µs

t

CSS

CS Setup Time

0.2

µs

DO Hold Time

70

ns

t

DIS

DI Setup Time

0.4

µs

CS Hold Time

0

ns

t

DIH

DI Hold Time

0.4

µs

t

PD

Output Delay

2

µs

CS to Status Valid

1

µs

t

DF

CS to DO in Hi-Z

CS = V

IL

0.4

µs

t

WP

Write Cycle Time

15

ms

Capacitance T

250 KHz (Note 6)

Symbol

Test

Typ

Max

Units

C

OUT

Output Capacitance

5

pF

C

IN

Input Capacitance

5

pF

Note 1:

Stress above those listed under “Absolute Maximum Ratings” may cause permanent damage

to the device. This is a stress rating only and functional operation of the device at these or any other

conditions above those indicated in the operational sections of the specification is not implied. Exposure

to absolute maximum rating conditions for extended periods may affect device reliability.

Note 2:

Typical leakage values are in the 20nA range.

Note 3:

ORG pin may draw >1

µA when in x8 mode due to the internal pull-up transistor.

Note 4:

The shortest allowable SK clock period = 1/f

SK clock speed (minimum SK period) is determined by the interaction of several AC parameters stated

in the datasheet. Within this SK period, both t

allowable to set 1/f

Note 5:

device registers (device reset) prior to beginning another opcode cycle. (This is shown in the opcode

diagram on the following page.)

Note 6:

This parameter is periodically sampled and not 100% tested.

AC Test Conditions

Input Levels

Timing Level

Timing Level

2.7V

≤ V

0.3V/1.8V

1.0V

0.8V/1.5V

±10µA

(Extended Voltage Levels)

4.5V

≤ V

0.4V/2.4V

1.0V/2.0V

0.4V/2.4V

2.1mA/-0.4mA

(TTL Levels)

Output Load: 1 TTL Gate (C