データシートサーチシステム |
|
DM112E データシート(PDF) 2 Page - MicroPower Direct, LLC |
|
DM112E データシート(HTML) 2 Page - MicroPower Direct, LLC |
2 / 2 page Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the side of the unit Model Number Input Output Load Regulation (%, Max) Efficiency (%, Typ) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min) Nominal Range Full-Load No-Load DM101E 5 4.5 - 5.5 273 30 5.0 200.0 20.0 15 73 500 DM102E 5 4.5 - 5.5 270 30 12.0 83.0 9.0 15 74 500 DM103E 5 4.5 - 5.5 263 30 15.0 67.0 7.0 15 76 500 DM104E 5 4.5 - 5.5 278 30 ±5.0 ±100.0 ±10.0 15 72 500 DM105E 5 4.5 - 5.5 256 30 ±12.0 ±42.0 ±5.0 15 78 500 DM106E 5 4.5 - 5.5 256 30 ±15.0 ±33.0 ±4.0 15 78 500 DM111E 12 10.8 - 13.2 107 15 5.0 200.0 20.0 15 78 200 DM112E 12 10.8 - 13.2 103 15 12.0 83.0 9.0 15 81 200 DM113E 12 10.8 - 13.2 105 15 15.0 67.0 7.0 15 79 200 DM114E 12 10.8 - 13.2 114 15 ±5.0 ±100.0 ±10.0 15 73 200 DM115E 12 10.8 - 13.2 105 15 ±12.0 ±42.0 ±5.0 15 79 200 DM116E 12 10.8 - 13.2 105 15 ±15.0 ±33.0 ±4.0 15 79 200 Pin Single Dual Pin Single Dual 1 +Vin +Vin 5 No Pin Common 2 -Vin -Vin 6 +Vout +Vout 4 -Vout -Vout Derating Curve g Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ce- ramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. An input capacitor will enhace stability over temperature and input line variations. Recommended capacitor values are given in the table above. For applications requiring very low output noise levels, a simple LC filter should be effective. 4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Vin Input Capacitor Vout Output Capacitor Single Dual 5 VDC 4.7 µF 5 VDC 10.0 µF 4.7 µF 12 VDC 2.2 µF 12 VDC 2.2 µF 1.0 µF 15 VDC 1.0 µF 0.47 µF Model Selection Guide Mechanical Dimensions Pin Connections MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com www.micropowerdirect.com |
同様の部品番号 - DM112E |
|
同様の説明 - DM112E |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |