データシートサーチシステム |
|
93AA46-SN データシート(PDF) 4 Page - Microchip Technology |
|
93AA46-SN データシート(HTML) 4 Page - Microchip Technology |
4 / 12 page 93AA46/56/66 DS20067G-page 4 © 1996 Microchip Technology Inc. 2.0 FUNCTIONAL DESCRIPTION When the ORG pin is connected to VCC, the (x16) orga- nization is selected. When it is connected to ground, the (x8) organization is selected. Instructions, addresses and write data are clocked into the DI pin on the rising edge of the clock (CLK). The DO pin is nor- mally held in a high-Z state except when reading data from the device, or when checking the READY/BUSY status during a programming operation. The ready/ busy status can be verified during an Erase/Write oper- ation by polling the DO pin; DO low indicates that pro- gramming is still in progress, while DO high indicates the device is ready. The DO will enter the high-Z state on the falling edge of the CS. 2.1 START Condition The START bit is detected by the device if CS and DI are both HIGH with respect to the positive edge of CLK for the first time. Before a START condition is detected, CS, CLK, and DI may change in any combination (except to that of a START condition), without resulting in any device oper- ation (READ, WRITE, ERASE, EWEN, EWDS, ERAL, and WRAL). As soon as CS is HIGH, the device is no longer in the standby mode. An instruction following a START condition will only be executed if the required amount of opcode, address and data bits for any particular instruction is clocked in. After execution of an instruction (i.e., clock in or out of the last required address or data bit) CLK and DI become don't care bits until a new start condition is detected. 2.2 DI/DO It is possible to connect the Data In and Data Out pins together. However, with this configuration it is possible for a “bus conflict” to occur during the “dummy zero” that precedes the READ operation, if A0 is a logic HIGH level. Under such a condition the voltage level seen at Data Out is undefined and will depend upon the relative impedances of Data Out and the signal source driving A0. The higher the current sourcing capability of A0, the higher the voltage at the Data Out pin. 2.3 Data Protection During power-up, all programming modes of operation are inhibited until VCC has reached a level greater than 1.4V. During power-down, the source data protection circuitry acts to inhibit all programming modes when VCC has fallen below 1.4V at nominal conditions. The EWEN and EWDS commands give additional pro- tection against accidentally programming during nor- mal operation. After power-up, the device is automatically in the EWDS mode. Therefore, an EWEN instruction must be performed before any ERASE or WRITE instruction can be executed. 2.4 READ The READ instruction outputs the serial data of the addressed memory location on the DO pin. A dummy zero bit precedes the 16 bit (x16 organization) or 8 bit (x8 organization) output string. The output data bits will toggle on the rising edge of the CLK and are stable after the specified time delay (TPD). Sequential read is pos- sible when CS is held high. The memory data will auto- matically cycle to the next register and output sequentially. 2.5 Erase/Write Enable and Disable (EWEN,EWDS) The 93AA46/56/66 power up in the Erase/Write Disable (EWDS) state. All programming modes must be pre- ceded by an Erase/Write Enable (EWEN) instruction. Once the EWEN instruction is executed, programming remains enabled until an EWDS instruction is executed or VCC is removed from the device. To protect against accidental data disturb, the EWDS instruction can be used to disable all Erase/Write functions and should fol- low all programming operations. Execution of a READ instruction is independent of both the EWEN and EWDS instructions. 2.6 ERASE The ERASE instruction forces all data bits of the spec- ified address to the logical “1” state. CS is brought low following the loading of the last address bit. This falling edge of the CS pin initiates the self-timed programming cycle. The DO pin indicates the READY/BUSY status of the device if CS is brought high after a minimum of 250 ns low (TCSL). DO at logical “0” indicates that program- ming is still in progress. DO at logical “1” indicates that the register at the specified address has been erased and the device is ready for another instruction. The ERASE cycle takes 4 ms per word typical. 2.7 WRITE The WRITE instruction is followed by 16 bits (or by 8 bits) of data which are written into the specified address. After the last data bit is put on the DI pin, CS must be brought low before the next rising edge of the CLK clock. This falling edge of CS initiates the self- timed auto-erase and programming cycle. The DO pin indicates the READY/BUSY status of the device if CS is brought high after a minimum of 250 ns low (TCSL) and before the entire write cycle is complete. DO at logical “0” indicates that programming is still in progress. DO at logical “1” indicates that the register at the specified address has been written with the data specified and the device is ready for another instruc- tion. The WRITE cycle takes 4 ms per word typical. |
同様の部品番号 - 93AA46-SN |
|
同様の説明 - 93AA46-SN |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |