データシートサーチシステム |
|
BTS426L1 データシート(PDF) 2 Page - Infineon Technologies AG |
|
BTS426L1 データシート(HTML) 2 Page - Infineon Technologies AG |
2 / 14 page BTS426L1 Semiconductor Group 2 2003-Oct-01 Pin Symbol Function 1 GND - Logic ground 2 IN I Input, activates the power switch in case of logical high signal 3 Vbb + Positive power supply voltage, the tab is shorted to this pin 4 ST S Diagnostic feedback, low on failure 5 OUT (Load, L) O Output to the load Maximum Ratings at Tj = 25 °C unless otherwise specified Parameter Symbol Values Unit Supply voltage (overvoltage protection see page 3) Vbb 43 V Supply voltage for full short circuit protection Tj Start=-40 ...+150°C Vbb 34 V Load dump protection2) VLoadDump = UA + Vs, UA = 13.5 V RI3)= 2 Ω, RL= 1.7 Ω, td= 200 ms, IN= low or high VLoad dump4) 60 V Load current (Short circuit current, see page 4) IL self-limited A Operating temperature range Storage temperature range Tj Tstg -40 ...+150 -55 ...+150 °C Power dissipation (DC), TC ≤ 25 °C Ptot 75 W Inductive load switch-off energy dissipation, single pulse Vbb =12V, Tj,start =150°C, TC =150°C const. IL = 7.0 A, ZL = 24 mH, 0 Ω: EAS 0.74 J Electrostatic discharge capability (ESD) IN: (Human Body Model) all other pins: acc. MIL-STD883D, method 3015.7 and ESD assn. std. S5.1-1993 VESD 1.0 2.0 kV Input voltage (DC) VIN -10 ... +16 V Current through input pin (DC) Current through status pin (DC) see internal circuit diagrams page 6 IIN IST ±2.0 ±5.0 mA Thermal Characteristics Parameter and Conditions Symbol Values Unit min typ max Thermal resistance chip - case: junction - ambient (free air): RthJC RthJA -- -- -- -- 1.67 75 K/W SMD version, device on PCB5): 34 2 ) Supply voltages higher than Vbb(AZ) require an external current limit for the GND and status pins, e.g. with a 150 Ω resistor in the GND connection and a 15 k Ω resistor in series with the status pin. A resistor for the protection of the input is integrated. 3) RI = internal resistance of the load dump test pulse generator 4) VLoad dump is setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839 5 ) Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm 2 (one layer, 70 µm thick) copper area for Vbb connection. PCB is vertical without blown air. |
同様の部品番号 - BTS426L1 |
|
同様の説明 - BTS426L1 |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |