データシートサーチシステム |
|
LM1229 データシート(PDF) 4 Page - Texas Instruments |
|
LM1229 データシート(HTML) 4 Page - Texas Instruments |
4 / 28 page OBSOLETE LM1229 SNOSAH0D – MARCH 2005 – REVISED APRIL 2013 www.ti.com Video Signal Electrical Characteristics Unless otherwise noted: TA = 25°C, VCC = +5.0V, VIN = 0.70 VP-P, VABL = VCC, CL = 10 pF, Video Outputs = 2.4 VP-P (1) (2) Symbol Parameter Conditions Min Typ Max Units IS Supply current No output loading(3) 260 330 mA IS-PS Supply current, power save mode No output loading(3) 100 125 mA VOB TYP Active video black level output No input signal, DC offset = 0x3. 1.25 V VOB MIN Active video minimum black level No input signal, DC offset = 0xF(min) 0.5 V output VOB MAX Active video maximum black level No input signal, DC offset = 0x0(max) 1.45 V output VOB STEP Active video black level step size No input signal. Varying DC offset. 65 mV VOB MIN BRITE Active video minimum black level No input signal, DC offset = 0x3, 0.8 V output gain = 0x7F, brightness.= 0xFF(min) VOB MAX BRITE Active video maximum black level No input signal, DC offset = 0x3, 1.65 V output gain = 0x7F, brightness.= 0x00(max) VOBB STEP No input signal, DC offset = 0x3, varying Active video brightness step size 6.3 mV brightness VO MAX Video in = 0.70 VP-P, contrast = 0x7F, Maximum video output 4.75 V brightness = 0x0, DC offset = 0x3 LE Linearity error Staircase input signal(4) 5 % tR (5) Video rise time 10% to 90%, AC input signal(6) 8 ns OSR Rising edge overshoot AC input signal(6) 2 % tF (5) Video fall time 90% to 10%, AC input signal(6) 8 ns OSF Falling edge overshoot AC input signal(6) 2 % BW Channel bandwidth ( −3 dB) AC input signal(6) 70 MHz SEP10 kHz Video amplifier 10 kHz isolation See(7) 70 dB SEP10 MHz Video amplifier 10 MHz isolation See(7) 50 dB AV MAX Video in = 0.70 VP-P, Maximum contrast Maximum voltage gain 4.35 V/V and gain, VABL = 5.0V AV 50% CONT Contrast attenuation @ 50% Maximum gain, VABL = 5.0V –5.15 dB AV MIN/ Maximum contrast attenuation. Maximum gain, VABL = 5.0V –20.5 dB AV MAX AV 50% GAIN Gain attenuation @ 50% Maximum contrast, VABL = 5.0V –4.15 dB AV MIN GAIN/ AV MAX Maximum gain attenuation Maximum contrast, VABL = 5.0V –12 dB GAIN AV MATCH Maximum gain match between Maximum contrast, VABL = 5.0V ±0.6 dB channels AV TRACK Gain tracking channel to channel AC input signal(8) ±0.6 dB VABL HIGH ABL control range upper limit AC input signal(9) 4.5 V VABL LOW ABL control range lower limit AC input signal(9) 2.5 V (1) Datasheet min/max specification limits are specified by design, test, or statistical analysis. The ensured specifications apply only for the test conditions listed. Some performance characteristics may change when the device is not operated under the listed test conditions. (2) Typical specifications are specified at +25°C and represent the most likely parametric norm. (3) The supply current specified is the quiescent current for VCC = 5V and with RL = ∞. Load resistors are not required and are not used in the test circuit, therefore all the supply current is used by the pre-amp. (4) Linearity Error is the maximum variation in step height of a 16 step staircase input signal waveform with a 0.7 VP-P level at the input. All 16 steps equal, with each at least 100 ns in duration. (5) dt/dVCC = 200*(t5.5V–t4.5V)/((t5.5V + t4.5V)) %/V, where: t5.5V is the rise or fall time at VCC = 5.5V, and t4.5V is the rise or fall time at VCC = 4.5V. (6) Input from signal generator: tr, tf < 1 ns. (7) Measure output levels of the other two undriven amplifiers relative to the driven amplifier to determine channel separation. Terminate the undriven amplifier inputs to simulate generator loading. Repeat test at fIN = 10 MHz for VSEP 10 MHz. (8) ΔAV track is a measure of the ability of any two amplifiers to track each other and quantifies the matching of the three gain stages. It is the difference in gain change between any two amplifiers with the contrast set to AV 50% and measured relative to the AV MAX condition. For example, at AV MAX the three amplifiers' gains might be 12.1 dB, 11.9 dB, and 11.8 dB and change to 2.2 dB, 1.9 dB and 1.7 dB respectively for contrast set to AV 50%. This yields a typical gain change of 10.0 dB with a tracking change of ±0.2 dB. (9) The ABL input provides smooth decrease in gain over the operational range of 0 dB to −5 dB: ΔAABL = AV MAX – AV (VABL = VABL MIN GAIN). Beyond −5 dB the gain characteristics, linearity and pulse response may depart from normal values. 4 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated Product Folder Links: LM1229 |
同様の部品番号 - LM1229 |
|
同様の説明 - LM1229 |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |