データシートサーチシステム |
|
AD7938BCP データシート(PDF) 7 Page - Analog Devices |
|
AD7938BCP データシート(HTML) 7 Page - Analog Devices |
7 / 32 page Preliminary Technical Data AD7938/AD7939 TIMING SPECIFICATIONS1 VDD = VDRIVE =2.7 V to 5.25V, Internal/External VREF = 2.5 V, unless otherwise noted, FCLKIN = 24 MHz, FSAMPLE = 1.5 MSPS; TA = TMIN to TMAX, unless otherwise noted. Table 3. Limit at TMIN, TMAX Parameter AD7938 AD7939 Unit Description fCLKIN2 10 10 kHz min 24 24 MHz max tQUIET 10 10 ns min Minimum time between end of Read and start of next conversion (i.e., time from when the data bus goes into three-state until the next falling edge of CONVST) t1 10 10 ns min CONVST Pulse Width. t2 20 20 ns min CONVST Falling Edge to CLKIN Falling Edge Setup Time. t3 TBD TBD ns min CLKIN Falling Edge to BUSY Rising Edge. t4 0 0 ns min CS to WR Setup Time. t5 0 0 ns min CS to WR Hold Time. t6 25 25 ns min WR Pulse Width. t7 10 10 ns min Data Setup Time before WR. t8 5 5 ns min Data Hold after WR. t9 0.5 tCLKIN 0.5 tCLKIN ns min New Data Valid before Falling Edge of BUSY. t10 0 0 ns min CS to RD Setup Time. t11 0 0 ns min CS to RD Hold Time. t12 55 55 ns min RD Pulse Width. t133 50 50 ns max Data Access Time after RD. t144 5 5 ns min Bus Relinquish Time after RD. 40 40 ns max Bus Relinquish Time after RD. t15 15 15 ns min HBEN to RD Setup Time. t16 5 5 ns min HBEN to RD Hold Time. t17 10 10 ns min Minimum Time between Reads/Writes. t18 0 0 ns min HBEN to WR Setup Time. t19 5 5 ns min HBEN to WR Hold Time. t20 TBD TBD ns max CLKIN Falling Edge to BUSY Falling Edge. 1Sample tested during initial release to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of VDD) and timed from a voltage level of 1.6 V. All timing specifications given above are with a 25 pF load capacitance (see , , and . Figure 38 Figure 39 Figure 40 Figure 41 2 Mark/space ratio for CLKIN is 40/60 to 60/40. 3 The time required for the output to cross TBD. 4 t14 is derived from the measured time taken by the data outputs to change 0.5 V. The measured number is then extrapolated back to remove the effects of charging or discharging the 25 pF capacitor. This means that the time, t14, quoted in the timing characteristics is the true bus relinquish time of the part and is independent of the bus loading. Rev. PrN | Page 7 of 32 |
同様の部品番号 - AD7938BCP |
|
同様の説明 - AD7938BCP |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |