データシートサーチシステム |
|
LM1238 データシート(PDF) 4 Page - National Semiconductor (TI) |
|
|
LM1238 データシート(HTML) 4 Page - National Semiconductor (TI) |
4 / 24 page DAC Output Electrical Characteristics (Continued) Unless otherwise noted: T A = 25˚C, VCC = +5.0V, VIN = 0.7V, VABL =VCC,CL = 8 pF, Video Outputs = 2.0 VP-P. See Note 7 for Min and Max parameters and Note 6 for Typicals. DAC parameters apply to all 4 DACs. Symbol Parameter Conditions Min Typ Max Units ∆V Max DAC (VCC) Variation in voltage of DAC with V CC 4.75 < V CC < 5.25V ±50 mV/V Linearity Linearity of DAC over its range 5 % Monotonicity Monotonicity of the DAC Excluding dead zones ±0.5 LSB I MAX Max Load Current −1.0 1.0 mA System Interface Signal Characteristics Unless otherwise noted: T A = 25˚C, VCC = +5.0V, VIN = 0.7V, VABL =VCC,CL = 8 pF, Video Outputs = 2.0 VP-P. See Note 7 for Min and Max parameters and Note 6 for Typicals. DAC parameters apply to all 4 DACs. Symbol Parameter Conditions Min Typ Max Units V VTH+ VFLYBACK positive switching guarantee. Vertical Blanking triggered 2.0 V V SPOT Spot Killer Voltage Note 17, V CC Adjusted to Activate 3.4 3.9 4.3 V V Ref V Ref Output Voltage 1.25 1.45 1.65 V V IL (SCL, SDA) Logic Low Input Voltage −0.5 1.5 V V IH (SCL, SDA) Logic High Input Voltage 3.0 V CC + 0.5 V I L (SCL, SDA) Logic Low Input Current SDA or SCL, Input Voltage = 0.4V ±10 µA I H (SCL, SDA) Logic High Input Voltage SDA or SCL, Input Voltage = 4.5V ±10 µA V OL (SCL, SDA) Logic Low Output Voltage I O = 3 mA 0.5 V f H Min Minimum Horizontal Frequency PLL & OSD Operational; PLL Range = 0 25 kHz f H Max Maximum Horizontal Frequency PLL & OSD Operational; PLL Range = 3 100 110 kHz I HFB IN Max Horizontal Flyback Input Current Absolute Maximum During Flyback 5 mA I IN Peak Current during flyback Design Value 4 mA I HFB OUT Max Horizontal Flyback Input Current Absolute Maximum During Scan −700 µA I OUT Peak Current during Scan Design Value −550 µA I IN THRESHOLD I IN H-Blank Detection Threshold 0 µA t H-BLANK ON H-Blank Time Delay - On + Zero crossing of I HFB to 50% of output blanking start. I 24 = +1.5mA 45 ns t H-BLANK OFF H-Blank Time Delay - Off − Zero crossing of I HFB to 50% of output blanking end. I 24 = −100µA 85 ns V BLANK Max Maximum Video Blanking Level Test Setting 4, AC input signal. 0 0.25 V f FREERUN Free Run H Frequency, including H Blank 42 kHz t PW CLAMP Minimum Clamp Pulse Width See Note 15 200 ns V CLAMP MAX Maximum Low Level Clamp Pulse Voltage Video Clamp Functioning 2.0 V V CLAMP MIN Minimum High Level Clamp Pulse Voltage Video Clamp Functioning 3.0 V I CLAMP Low Clamp Gate Low Input Current V 23 = 2V −0.4 µA I CLAMP High Clamp Gate High Input Current V 23 = 3V 0.4 µA t CLAMP-VIDEO Time from End of Clamp Pulse to Start of Video Referenced to Blue, Red and Green inputs 50 ns Note 1: Limits of Absolute Maximum Ratings indicate below which damage to the device must not occur. Note 2: Limits of operating ratings indicate required boundaries of conditions for which the device is functional, but may not meet specific performance limits. Note 3: All voltages are measured with respect to GND, unless otherwise specified. Note 4: Human body model, 100 pF discharged through a 1.5 k Ω resistor. www.national.com 4 |
同様の部品番号 - LM1238 |
|
同様の説明 - LM1238 |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |