データシートサーチシステム
  Japanese  ▼
ALLDATASHEET.JP

X  

LM1295N データシート(PDF) 8 Page - National Semiconductor (TI)

[Old version datasheet] Texas Instruments acquired National semiconductor.
部品番号 LM1295N
部品情報  DC Controlled Geometry Correction System for Continuous Sync Monitors
Download  11 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
メーカー  NSC [National Semiconductor (TI)]
ホームページ  http://www.national.com
Logo NSC - National Semiconductor (TI)

LM1295N データシート(HTML) 8 Page - National Semiconductor (TI)

Back Button LM1295N Datasheet HTML 3Page - National Semiconductor (TI) LM1295N Datasheet HTML 4Page - National Semiconductor (TI) LM1295N Datasheet HTML 5Page - National Semiconductor (TI) LM1295N Datasheet HTML 6Page - National Semiconductor (TI) LM1295N Datasheet HTML 7Page - National Semiconductor (TI) LM1295N Datasheet HTML 8Page - National Semiconductor (TI) LM1295N Datasheet HTML 9Page - National Semiconductor (TI) LM1295N Datasheet HTML 10Page - National Semiconductor (TI) LM1295N Datasheet HTML 11Page - National Semiconductor (TI)  
Zoom Inzoom in Zoom Outzoom out
 8 / 11 page
background image
Pin Descriptions
See
Figure 4 through Figure 8 for Input and Output schemat-
ics.
GND (Pin 1): This pin should be connected to the power
ground at pin 17.
V Height (Pin 2): Vertical Height. A voltage between 0V and
4V on this pin controls the amplitude of the +V and −V Drive
currents, with increasing voltage giving increasing current.
The control range is approximately 1.8 to 1. The response
time is slow, being limited by the automatic level control loop.
4 V Cap (Pin 3): 4 Volt Cap Capacitor. A 10 µF capacitor,
aluminum electrolytic or tantalum, should be connected be-
tween pin 3 (positive side) and GND (pin 17) to bypass the
internal 4V reference.
V Sync In (Pin 4): Vertical Sync Input. The vertical sync in-
put takes a negative-going TTL level pulse which injection
locks the vertical oscillator to the vertical sync frequency if it
is above the LM1295 minimum frequency. The input thresh-
old level is approximately 2V, so pulses other than TTL level
are satisfactory as long as they cross the 2V threshold with
at least a 400 mV margin either side. The minimum pulse
width is approximately 200 ns. For free-running detection (no
V Sync in), this input should be at logic high.
8 V Cap (Pin 5): 8 Volt Capacitor. A 100 µF capacitor, alumi-
num electrolytic or tantalum, should be connected between
pin 5 (positive side) and GND (pin 17) to bypass the internal
8V reference.
V Dyn Height (Pin 6): Vertical Dynamic Height. A voltage
between 3V and 4V on this pin controls the amplitude of the
+V and −V Drive currents with increasing voltage giving in-
creasing current. The control range is approximately
1.3 to 1. The bandwidth of this input is DC to greater than
125 kHz in contrast to the slow Vertical Height input.
V
CC (Pin 7): Power, 12V nominal. VCC should be bypassed
to GND (pin 17) with a 10 µF aluminum electrolytic or tanta-
lum capacitor.
Vref Cap (Pin 8): Voltage Reference Cap. A 10 µF capacitor,
aluminum electrolytic or tantalum, should be connected be-
tween pin 8 (positive side) and GND (pin 17).
H Dyn Width (Pin 9): Horizontal Dynamic Width. This output
consists of the sum of the vertical ramp and the parabola de-
rived from the ramp. The amplitude and polarity of the ramp
signal is DC controlled by H Trap Cntl (pin 11) and of the pa-
rabola by E-W Pin Cntl (pin 10). The weighting of the ramp is
1
3 the parabola; i.e., with the H Trap and E-W Pin Cntls at
4V, the output is 3 parts parabola and 1 part ramp. Horizontal
Dynamic Width is used to correct for trapezoid and east-west
pincushion distortion. The output stage is similar to a stan-
dard op-amp output. The bandwidth from either of the 2 con-
trol pins to the output is DC to greater than 125 kHz.
E-W Pin Cntl (Pin 10): East-West Pincushion Control. A
voltage of 0V to 4V adjusts the polarity and the amount of
parabola in the Horizontal Dynamic Width (pin 9) output. At
approximately 2V, the amount is zero. From 2V to 4V, the
amplitude increases and the parabola is positive-going.
From 2V to 0V, the amplitude increases and the parabola is
negative-going.
H Trap Cntl (Pin 11): Horizontal Trapezoid Control. A volt-
age of 0V to 4V adjusts the polarity and the amount of verti-
cal ramp in the Horizontal Dynamic Width (pin 9) output. At
approximately 2V, the amount is zero. From 2V to 4V, the
amplitude increases and the ramp is positive-going. From 2V
to
0V,
the
amplitude
increases
and
the
ramp
is
negative-going.
H Para Cntl (Pin 12): Horizontal Parallelogram Control. A
voltage of 0V to 4V adjusts the polarity and the amount of
vertical ramp in the Horizontal Dynamic Center (pin 14) out-
put. At approximately 2V, the amount is zero. From 2V to 4V,
the amplitude increases and the ramp is positive-going.
From 2V to 0V, the amplitude increases and the ramp is
negative-going.
H Bow Cntl (Pin 13): Horizontal Bow Control. A voltage of
0V to 4V adjusts the polarity and the amount of parabola in
the Horizontal Dynamic Center (pin 14) output. At approxi-
mately 2V, the amount is zero. From 2V to 4V, the amplitude
increases and the parabola is positive-going. From 2V to 0V,
the amplitude increases and the parabola is negative-going.
H Dyn Cntr (Pin 14): Horizontal Dynamic Center. This out-
put consists of the sum of the vertical ramp and the parabola
derived from the ramp. The amplitude and polarity of the
ramp signal is DC controlled by H Para Cntl (pin 12) and of
the parabola by H Bow Cntl (pin 13). The difference between
this output and the Horizontal Dynamic Width output is in the
weighting of the ramp, which is equal to the parabola; i.e.,
with the H Para and H Bow Cntls at 4V, the output is 1 part
parabola and 1 part ramp. Horizontal Dynamic Center is
used to correct for parallelogram and bow distortion. The
output stage is similar to a standard op-amp output. The
bandwidth from either of the 2 control pins to the output is
DC to greater than 125 kHz.
V Dyn Focus Cntl (Pin 15): Vertical Dynamic Focus Con-
trol. A voltage of 0V to 4V adjusts the polarity and the amount
of parabola in the Vertical Dynamic Focus (pin 16) output. At
approximately 2V, the amount is zero. From 2V to 4V, the
amplitude increases and the parabola is positivegoing. From
2V to 0V, the amplitude increases and the parabola is
negative-going.
V Dyn Focus (Pin 16): Vertical Dynamic Focus. This output
consists of the parabola derived from the vertical ramp. The
amplitude and polarity are controlled by V Dyn Focus Cntl.
The output stage is similar to a standard op-amp output. The
bandwidth from the control pin to the output is DC to greater
than 125 kHz.
GND (Pin 17): Ground. This is the power supply ground for
the 12V supply and the point to which the bypass capacitors
are returned.
ALC Cap (Pin 18): Automatic Level Control Capacitor. This
capacitor is part of the level control circuit that maintains
constant vertical height in spite of vertical sync frequency
changes. The recommended value is 4.7 µF, aluminum elec-
trolytic or tantalum capacitor. If the VCO capacitor value is
changed, this capacitor value should change in the same ra-
tio. A 300k resistor should be connected from this pin to
ground.
2f Cap (Pin 19): Double frequency Capacitor. This capacitor
prevents the vertical oscillator from locking at twice the ver-
tical sync frequency. The recommended value is 0.47 µF. If
the VCO capacitor value is changed, this capacitor value
should change in the same ratio.
Osc Cap (Pin 20): A timing capacitor is connected from this
pin to ground for the internal oscillator. The capacitance de-
termines the lowest lock frequency. See Graph 1.
Rvert (Pin 21): Vertical Resistor. One end of the Vertical Re-
sistor connects to this pin. This resistor determines the gain
of the vertical ramp current generator. The gain is inversely
proportional to the resistance. It is recommended that this be
a standard 5% 14W carbon film resistor whose negative tem-
www.national.com
8


同様の部品番号 - LM1295N

メーカー部品番号データシート部品情報
logo
National Semiconductor ...
LM129 NSC-LM129 Datasheet
165Kb / 10P
   Precision Reference
logo
Linear Technology
LM129 LINER-LM129 Datasheet
179Kb / 4P
   6.9V Precision Voltage Reference
LM129 LINER-LM129 Datasheet
125Kb / 4P
   6.9V Precision Voltage Reference
LM129 LINER-LM129 Datasheet
166Kb / 8P
   6.9V Precision Voltage Reference
logo
National Semiconductor ...
LM1290 NSC-LM1290 Datasheet
176Kb / 9P
   Autosync Horizontal Deflection Processor
More results

同様の説明 - LM1295N

メーカー部品番号データシート部品情報
logo
National Semiconductor ...
LM1291 NSC-LM1291 Datasheet
205Kb / 12P
   Video PLL System for Continuous-Sync Monitors
LM1292 NSC-LM1292 Datasheet
217Kb / 10P
   Video PLL System for Continuous-Sync Monitors
LM1296 NSC-LM1296 Datasheet
236Kb / 10P
   Raster Geometry Correction System for Multi-Frequency Displays
logo
Asahi Kasei Microsystem...
AK2345 AKM-AK2345 Datasheet
1Mb / 27P
   CTCSS(Continuous Tone Controlled Squelch System
logo
NXP Semiconductors
TDA4810 PHILIPS-TDA4810 Datasheet
968Kb / 14P
   SYNC PROCESSOR AND HORIZONTAL DRIVE FOR MONITORS
May 1991
logo
TEMIC Semiconductors
U2203B TEMIC-U2203B Datasheet
106Kb / 7P
   RGB Video Amplifier System for Monitors
logo
Sanyo Semicon Device
LC7070N SANYO-LC7070N Datasheet
195Kb / 8P
   Sync and Error Detection & Correction LSIs for RDS
logo
STMicroelectronics
TDA8176 STMICROELECTRONICS-TDA8176 Datasheet
94Kb / 5P
   TV VERTICAL DEFLECTION SYSTEM FOR TV AND MONITORS
logo
Sanken electric
SSC2001S SANKEN-SSC2001S Datasheet
213Kb / 8P
   Power Factor Correction Continuous Conduction Mode Controller
logo
STMicroelectronics
STV9306A STMICROELECTRONICS-STV9306A Datasheet
762Kb / 16P
   Bus-Controlled Vertical Deflection System with East/West Correction Output Circuit
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11


データシート ダウンロード

Go To PDF Page


リンク URL




プライバシーポリシー
ALLDATASHEET.JP
ALLDATASHEETはお客様のビジネスに役立ちますか?  [ DONATE ] 

Alldatasheetは   |   広告   |   お問い合わせ   |   プライバシーポリシー   |   リンク交換   |   メーカーリスト
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com