データシートサーチシステム |
|
LM2413T データシート(PDF) 6 Page - National Semiconductor (TI) |
|
|
LM2413T データシート(HTML) 6 Page - National Semiconductor (TI) |
6 / 11 page Application Hints (Continued) PC Board Layout Considerations For optimum performance, an adequate ground plane, isola- tion between channels, good supply bypassing and minimiz- ing unwanted feedback are necessary. Also, the length of the signal traces from the preamplifier to the LM2413 and from the LM2413 to the CRT cathode should be as short as possible. The red video trace from the LM1283 to the LM2413 input should be considered as short as possible on a PCB layout. If possible, position the pre-amp in such a way where the traces from its output connects to the driver input the most direct and shortest path. The following references are recommended for video board designers: Ott, Henry W., “Noise Reduction Techniques in Electronic Systems”, John Wiley & Sons, New York, 1976. “Guide to CRT Video Design”, National Semiconductor Appli- cation Note 861. “Video Amplifier Design for Computer Monitors”, National Semiconductor Application Note 1013. Pease, Robert A., “Troubleshooting Analog Circuits”, Butterworth-Heinemann, 1991. Because of its high small signal bandwidth, the part may os- cillate in a monitor if feedback occurs around the video chan- nel through the chassis wiring. To prevent this, leads to the video amplifier input circuit should be shielded, and input cir- cuit wiring should be spaced as far as possible from output circuit wiring. NSC Demonstration Board Figure 11 and Figure 12 show routing and component place- ment on the NSC LM1283/2413 demonstration board. The schematic of the board is shown in Figure 10. This board provides a good example of a layout that can be used as a guide for future layouts. Note the location of the following components: • C79 —V CC bypass capacitor, located very close to pin 6 and ground pins. ( Figure 12) • C55 —V BB bypass capacitor, located close to pin 10 and ground. ( Figure 12) • C75 and C77 —V CC bypass capacitors, near LM2413 and V CC clamp diodes. Very important for arc protection. ( Figure 11) The routing of the LM2413 outputs to the CRT is very critical to achieving optimum performance. Figure 13 shows the routing and component placement from pin 1 to the blue cathode. Note that the components are placed so that they almost line up from the output pin of the LM2413 to the blue cathode pin of the CRT connector. This is done to minimize the length of the video path between these two components. Note also that D14, D15, R29 and D13 are placed to keep the size of the video nodes to a minimum. This minimizes parasitic capacitance in the video path and also enhances the effectiveness of the protection diodes. The anode of pro- tection diode D14 is connected directly to a section of the ground plane that has a short and direct path to the LM2413 ground pins. The cathode of D15 is connected to V CC very close to decoupling capacitor C55 (see Figure 13) which is connected to the same section of the ground plane as D14. The diode placement and routing is very important for mini- mizing the voltage stress on the LM2413 during an arc over event. Lastly, notice that S3 is placed very close to the blue cathode and is tied directly to CRT ground. www.national.com 6 |
同様の部品番号 - LM2413T |
|
同様の説明 - LM2413T |
|
|
リンク URL |
プライバシーポリシー |
ALLDATASHEET.JP |
ALLDATASHEETはお客様のビジネスに役立ちますか? [ DONATE ] |
Alldatasheetは | 広告 | お問い合わせ | プライバシーポリシー | リンク交換 | メーカーリスト All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |